[Top] [Contents] [Index] [ ? ]

Fdutils

General Introduction

Fdutils is a collection of utililties for configuring and using the Linux floppy driver. With fdutils, you can:

  1. Format disks with a higher capacity than usual (up to 1992KB on a 3 1/2 HD disk).
  2. Reconfigure the autodetection sequence to automatically detect some of these extended formats.
  3. Access various internal driver structures and drive configuration using the floppycontrol program.

This manual describes these utilities, and also the floppy driver itself.

1. Where to get fdutils and its documentation  
2. Basic usage  How to get started
3. Device numbers  
4. Media description  How can a floppy disk and a format be described to fdutils?
5. Drive descriptions  How can a drive and its characteristics be described to fdutils?
6. Storing more data on a floppy disk  How to store more data on your floppy disks
7. How autodetection works  How the floppy driver distinguishes among the different kinds of disks
8. Configuring the floppy driver via lilo or insmod  Lilo boot options understood by the floppy driver
9. Floppy ioctls  The ioctl's understood by the floppy driver
10. Command list  The available fdutils commands
11. Compile-time configuration via GNU autoconf  How to use GNU autoconf to customize fdutils
A. Acronyms  A brief listing of acronyms used in this documentation
B. Interesting formats  A brief list of legacy and other formats
Command Index  
Concept index  Concept Index


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

1. Where to get fdutils and its documentation

Fdutils can be found at the following places (+ mirrors):
 
ftp://www.tux.org/pub/knaff/fdutils/fdutils-5.5.tar.gz
ftp://metalab.unc.edu/pub/Linux/utils/disk-management/fdutils-5.5.tar.gz
ftp://tsx-11.mit.edu/pub/linux/sources/sbin/fdutils-5.5.tar.gz

The FAQ included in this package is also available separetely at:
 
http://alain.knaff.linux.lu/floppy/FAQ.html
http://www.tux.org/pub/knaff/floppy/FAQ.html
The FAQ at fdutils.linux.lu and www.tux.org is usually more up to date than versions found elsewhere. Thus, if you don't find an answer in the copy of the FAQ you have, please check this one for more recent info.

Before reporting a bug, make sure that it has not yet been fixed in the Alpha patches which can be found at:
 
http://fdutils.linux.lu
ftp://www.tux.org/pub/knaff/fdutils

These patches are named fdutils-version-ddmm.taz, where version stands for the base version, dd for the day and mm for the month. Due to a lack of space, I usually leave only the most recent patch.

There is an fdutils mailing list at fdutils @ www.tux.org . Please send all bug reports to this list. You may subscribe to the list by sending a message with 'subscribe fdutils @ www.tux.org' in its body to majordomo @ www.tux.org . (N.B. Please remove the spaces around the "@" both times. I left them there in order to fool spambots.) Announcements of new fdutils versions will also be sent to the list, in addition to the linux announce newsgroups. The mailing list is archived at http://www.tux.org/hypermail/fdutils/latest


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2. Basic usage

This chapter describes basic usage of floppies, and gives a few simple tips for using floppies under Linux.

2.1 How disks are organized  How a disk is organized, high-level and low-level formats
2.2 File systems supported by Linux  Which file systems does Linux support
2.3 What's in a name  How floppy drives are named
2.4 What to do if you get an unidentified floppy disk  How to identify a disk
2.5 Nickel tours  Short summaries of the various storage methods
2.7 New Features of 1.2+ kernels  New features of the kernel, mtools, and fdutils


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.1 How disks are organized

All floppies have two levels of formatting, both of which must be known in order to read them. The first is the binary or sector level format, which is how raw data is stored on the disk. The second is a higher level organization, often called a file system, which allows multiple files to be conveniently stored on the disk.

For example, a typical 1.44MB disk contains a low-level format, with 18 sectors per track, 80 tracks, and two sides (or heads); each sector can hold 512 bytes of data for a total of 1474560 bytes (or 1440 KB). When used under MS-DOS, this floppy would have a small portion of the disk used to keep track of files on the disk (including a bootsector, file allocation tables, directories, etc.).

The floppy driver generally takes care of reading the binary, or low-level format. It can often "guess" the low-level disk geometry needed to read the disk. This is called autodetection (see section 7. How autodetection works). If the driver can't autodetect the disk (e.g. if it is in an unusual format) you can tell the driver what the geometry is either by using the setfdprm (see section 10.9 setfdprm) utility or by using a fixed geometry device device (e.g. `/dev/fd0H1440').

Under Linux, many different file systems from many sources can be used. Some of these file systems are interpreted via a utility program (for example mtools for using disks with an MS-DOS file system). Many file systems can alternatively be "mounted" to appear in the UNIX directory structure until subsequently being unmounted; this is usually implemented by having the kernel itself interpret the file system on the disk.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.2 File systems supported by Linux

The following file systems are supported:

OS/2 HPFS:
read-only support (mount/kernel)
Mac HPFS 1.44MB:
read-only (xhfs utility)
MS-DOS:
read, write, format (mtools utility and mount/kernel)
tar, cpio:
compatible with many variations of UNIX (tar, cpio utilities)
System V, minix, xia, ext, ext2:
(mount/kernel)
pure binary disk access:
no file system (any program, usually dd, cat, and cp)


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.3 What's in a name

The following figure shows the meaning of the different parts of the name of a floppy device:

 
 +--------------- /dev: directory for devices
 |   +------------- fd: floppy disk device prefix
 |   | +------------ 0: floppy drive #0 (A:) (0-1 typical, 0-7
 |   | |                possible)
 |   | |+-- 3.5" drive: (use d for 5.25" double density drives, and
 |   | ||                    h for 5.25" high density drives,
 |   | ||                    u for 3.5" drive of any density)
 |   | ||   +---- 1440: Capacity (in KB) of format (usually between
 |   | ||   |           360 and 3920)
/dev/fd0u1440


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.4 What to do if you get an unidentified floppy disk

 
dd if=/dev/fd0 of=/tmp/foo count=1
        # If it works:
getfdprm                # This will report what geometry the disk has
file /tmp/foo           # This may indicate the type of file system
mdir a:                 # Check for an MS-DOS file system
tar tvf /dev/fd0        # Check for a tar archive
cpio -itv < /dev/fd0    # Check for a cpio archive
e2fsck /dev/fd0         # Check for an "ext2" file system
        # If it doesn't work:
        # Try the above dd command using various /dev/fd0* devices


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.5 Nickel tours

2.5.1 mtools  Access MS-Dos disks from Unix
2.5.2 Tar (Tape ARchive)  Tarring files directly to floppy disks
2.5.3 CPIO (CoPy In/Out)  Another archive format
2.6 Ext2 (Second Extended File System)  Seconded Extended File System


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.5.1 mtools

 
mdir a:                # Read directory of MS-DOS disk in drive A:
mcopy /tmp/foo\* a:    # Copy files beginning with foo in /tmp to A:
mcopy a:\* .           # Copy all files from A: to current directory
mformat a:             # Add MS-DOS file system to formatted disk


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.5.2 Tar (Tape ARchive)

 
tar tvf /dev/fd0              # Read directory of tar archive in
                              # drive A:
tar cvf /dev/fd0 foo1 foo2    # Write foo1 and foo2 to A: in tar
                              # format foo1/foo2 can be entire
                              # directory trees
tar xvfp /dev/fd0             # extract entire tar archive in
                              # drive A:

Tar is not a file system. Only low-level format (superformat, see section 10.10 superformat) are needed to prepare a disk to accept a tar archive.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.5.3 CPIO (CoPy In/Out)

 
cpio -itv < /dev/fd0        # Read directory of cpio archive in A:
find foo1 foo2 -print | cpio -ov < /dev/fd0
                            # Write foo1/foo2 to A:
                            # foo1/foo2 can be entire directory trees
cpio -idumv < /dev/fd0      # extract entire CPIO archive in drive A:

Note: blocks reported are in 512-byte units (due to UNIX System V heritage). Cpio is not a file system. Only low-level format (fdformat or superformat (see section 10.10 superformat) needed.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.6 Ext2 (Second Extended File System)

 
mke2fs /dev/fd0 1440          # Makes an ext2 filesystem of 1440
                              # block on A:
mke2fs -c /dev/fd0 1440       # Same as above, but tests floppy first
e2fsck /dev/fd0               # Tests filesystem integrity. (like
                              # chkdsk in Dos)
e2fsck -p /dev/fd0            # Repairs filesystem. (like chkdsk /f
                              # in Dos)
mount -t ext2 /dev/fd0 /mnt   # Mounts the disk in A: on /mnt.
                              # The directory /mnt must already exist
umount /mnt                   # Unmounts /mnt. No process should
                              # have its working directory in /mnt
                              # No process should have open files in
                              # /mnt

Note: don't use ext2 on 2m disks On some systems mke2fs is also called mkfs.ext2, and e2fsck is also called fsck.ext2


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.7 New Features of 1.2+ kernels

2.7.1 New features of 1.2+ kernels  New kernel features since 1.2.0
2.7.2 New features of mtools-3.0  New mtools features since mtools-3.0
2.7.3 New Utilities  Utilities contained in the fdutils package


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.7.1 New features of 1.2+ kernels


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.7.2 New features of mtools-3.0

NOTE: Mtools has no longer maintained by its original maintainer Emmet P. Gray after 2.0.7.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

2.7.3 New Utilities


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

3. Device numbers

The floppy device nodes are usually made using the MAKEFLOPPIES shell script (See section 10.8 makefloppies.).

The major device number for the floppy drives is 2. The minor device number contains describes which drive it represents, and may in addition describe the kind of media which is currently in the drive.

There are two kind of floppy devices:

In this formula, fdc_nr is the number of the floppy disk controller (0 or 1, usually 0), and unit_nr is the Unit number (0 to 3, 0 for Dos drive A:, and 1 for Dos drive B:). Format_nr is only meaningful for the fixed format devices. It describes the disk geometry that is used. It is an index into the geometry list 3.3 The geometry list. Using all available controller numbers and all available drive numbers, you may thus connect up to 8 floppy drives to a single Linux box.

3.1 Variable format devices  
3.2 Fixed format devices  
3.3 The geometry list  
3.4 Adding new formats  


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

3.1 Variable format devices

Variable format devices don't have an intrinsic geometry. When using these devices, the geometry has to be set either by using autodetection (see section 7. How autodetection works), or by using the FDSETPRM or FDGETPRM ioctl. The latter ioctl can be issued using the setfdprm (see section 10.9 setfdprm) and getfdrpm (see section 10.7 getfdprm) programs. With the default settings, common formats are detected transparently, and you can access any disk transparently using the variable format devices.

The geometry information is kept as long as the disk is in the drive, and is discarded as soon as the disk is removed, unless the geometry has been declared permanent by using setfdprm's -p flag (see section 10.9 setfdprm).


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

3.2 Fixed format devices

Fixed format devices should not be used under normal circumstances.

Fixed format devices have an intrinsic geometry. They are useful for the fdformat program (which is now considered obsolete), and for booting off floppies which have formats that are different from the default format (because during booting, there is no application that can issue the otherwise needed FDSETPRM ioctl).


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

3.3 The geometry list

The floppy driver contains a builtin list of 32 formats. This list is used for two purposes:

The following formats (geometries) are known:

format_nr
Format
0
autodetect
1
360KB, 5.25" DD drive
2
1200KB, 5.25" HD drive
3
360KB, 3.5" DD drive
4
720KB, 3.5" DD drive
5
360KB, 5.25" DD disk in HD drive
6
720KB, 5.25" DD disk in HD drive
7
1440KB, 3.5" HD drive
8
2880KB, 3.5" ED drive
9
3120KB, 3.5" ED drive
10
1440KB, 5.25" HD drive
11
1680KB, 3.5" HD drive
12
410KB, 5.25" DD disk in HD drive
13
820KB, 3.5" DD drive
14
1476KB, 5.25" HD drive
15
1722KB, 3.5" HD drive
16
420KB, 5.25" DD disk in HD drive
17
830KB, 3.5" DD drive
18
1494KB, 5.25" HD drive
19
1743KB, 3.5" HD drive
20
880KB, 5.25" DD drive
21
1040KB, 3.5" DD drive
22
1120KB, 3.5" DD drive
23
1600KB, 5.25" HD drive
24
1760KB, 3.5" HD drive
25
1920KB, 3.5" HD drive
26
3200KB, 3.5" ED drive
27
3520KB, 3.5" ED drive
28
3840KB, 3.5" ED drive
29
1840KB, 3.5" HD drive
30
800KB, 3.5" DD drive
31
1600KB, 3.5" HD drive

This table lists first the format_nr (0-31) used to compute the minor number, then the capacity of the format (360KB - 3200KB), and then the type of the drive in which this format is used.

The formats 0..8 are the standard PC formats. The remaining formats are extended capacity formats. Some of them have been taken from Heiko Schroeder's fdpatches (after correcting some minor bugs). Others have been added by David Niemi and me (Alain Knaff). Formats 9, 12, 13, 16, 17, 30 and 31 are non-interleaved formats with normal sized sectors, and have the highest capacity that can be achieved without resorting to interleaving or bigger sectors (6.1 More sectors per cylinder). Formats 10, 11, 14, 15, 18, 19 use interleaving interleaving to achieve a higher capacity (6.2 Using interleave). Formats 20 and 22 to 29 use bigger sectors than usual (6.5 Larger sectors and 6.6 Mixed sector size (MSS) formats).

In addition to these techniques, formats 13-19 use more cylinders than usual (6.4 More Cylinders). USE THESE FORMATS (13-19) ONLY IF YOUR DRIVE SUPPORTS THE NECESSARY NUMBER OF TRACKS


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

3.4 Adding new formats

You can redefine the default formats using the setfdprm program (10.9 setfdprm) (1). The following example illustrates how to add a new 19 sector format, and make a device entry for it. First, we pick an entry for it, which we want to reuse. I recommend to redefine an entry which is only rarely used. For instance, if you have no 5 1/4 drive on your system, you can redefine any 5 1/4 entry without a loss. In our example, we pick 10.

First we make the device node:
 
mknod /dev/fd0H1520 b 2 40
         ^          ^ ^  ^
         |          | |  Minor device number (format number * 4 +
         |          | |                       drive + controller*128)
         |          | Major device number (always 2!)           
         |          Blockdevice
    A name that you choose for the format. I
    recommend to base the name on the capacity,
    but you may choose any name you want.

Then we redefine the geometry of the new device:
 
setfdprm /dev/fd0H1520 1520 19 2 80 0 0x1b 0 0xcf 0x6c

Note: This redefines the geometry for any device node with the same format number, not just the new node.

The new geometry is only valid until the next reboot (or removal of the floppy module). In order to make it permanent, you have to execute the setfdprm command from your `/etc/rc' file or whenever you insert the floppy module.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

4. Media description

4.1 Introduction  Benefits of the new representation
4.2 Syntax  What a media description looks like
4.3 The media description dictionary in /etc/fdmediaprm  Refer to media by a symbolic name


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

4.1 Introduction

Fdutils-5.0 introduces a new uniform format description, which is supported both by setfdprm and superformat. The new format description is easyer to handle, because it allows to set the different parameters of a format description in a symbolic and position independant way, using a series of variable=value clauses. Moreover, it automatically fills in sensible default values for unspecified parameters. Thus you only need to describe those aspects of the format that are important to you, and let the system handle the others.

Moreover, the new description separates those aspects that were specific to the drive (like for instance its rotation speed) from those that are specific to the media (spacial density, number of sectors, etc.).

The same description can be used both by setfdprm and superformat:
 
setfdprm /dev/fd0 hd sect=21 cyl=83
superformat /dev/fd0 hd sect=21 cyl=83

The first line above configures a 21 sector/83 cylinder format for drive 0, and the second line formats a disk using this same format.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

4.2 Syntax

A media description is a series of variable=value and selector clauses. Value is a number followed by an optional unit. The unit is either KB (1024 bytes) or b (blocks of 512 bytes), or none (bytes).

4.2.1 Selecting the density  
4.2.2 Selecting the number of cylinders, heads and sectors  
4.2.3 Selecting non-standard sector sizes  
4.2.4 Legacy formats  
4.2.5 Expert options  


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

4.2.1 Selecting the density

To select a density just insert its two letter code into the format description. Selecting a density also selects its default number of sectors, heads and cylinders. However, these latter parameters can be overridden.

hd
High density (1440KB for 3 1/2 and 1200KB for 5 1/4). The most commonly used format today.

dd
Double density (720KB for 3 1/2 and 360KB for 5 1/4)

ed
Extra density (2880KB for 3 1/2)

qd
Quad density (720KB for 5 1/4).

sd
Single density (no nominal size). Used mostly for CP/M. Only for experienced users.

If no density is given, the maximal density supported by the drive is used. However, in order to keep the drive description and the media description independent, I strongly suggest that you always indicate the density anyways.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

4.2.2 Selecting the number of cylinders, heads and sectors

This subsection describes how to select custom formats with a non-standard number of heads, cylinders or sectors. However, note that just describing the number of sectors, heads and cylinders is not enough: you also need to indicate which density your custom format is based on (cf. previous section).

sect=nb_of_sectors
This describes the number of sectors.
head=nb_of_heads
This describes the number of heads to be used.
cyl=nb_of_cylinders
This described the number of cylinders to be used.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

4.2.3 Selecting non-standard sector sizes

In order to achieve a higher capacity, you may want to use a bigger sector size.

ssize=sector_size
Choses a bigger sector size. The sector size is expressed in bytes. Only powers of two between 128 and 32768 are acceptable
sect=nb_of_sectors
Describes the number of sectors. For example hd sect=11 ssize=1024 describes a format where one track (1 side) is made up of 11 sectors of 1024 bytes each (thus 11KB per track, and 22KB per cylinder).
tracksize=size_of_one_track
Describes the size of one track. For example, hd tracksize=11KB ssize=1KB describes a format where one track contains 11KB of data (tracksize) stored in sectors of 1KB each.

This option exists mainly to describe MSS (mixed sector size) formats. For example, hd tracksize=12KB mss describes a format where one track which contains 12 KB of data. The sectors size are chosen by the system in a way to take up the least raw space: 8KB + 4KB.

mss

This option says that the format is an MSS format.

2m

This option says that the format is a so-called 2M format. These formats are intended for easy readability on DOS boxes. Their first track has the usual 18 sectors, whereas the other tracks have bigger sector, and in some cases mixed sector sizes.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

4.2.4 Legacy formats

The swapsides format allows to descibe disks whose sides are swapped, such as CBM1581 disks.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

4.2.5 Expert options

The following options are not needed in most common situations, as they are implied by the density selector. They may be needed to read some legacy (CP/M) formats.

tpi=48
For 5 1/4 disks only. This says that the format uses double-spaced cylinders (implied by double density).
tpi=96
For 5 1/4 disks only. This says that the format uses single-spaced cylinders (implied by quad and high density).
fm=0
Uses MFM encoding (implied by double, quad, high and extra density)
fm=1
Uses FM encoding (implied by single density)
dtr=dtr-code
Sets the data transfer rate. The following table lists the dtr codes for various transfer rates:
 
dtr-code    rate for FM          rate for MFM
=============================================
0           250kb/s              500kb/s
1           150kb/s              300kb/s
2           125kb/s              250kb/s
3           500kb/s              1000kb/s
perp=0
Do not use "perpendicular mode" sector headers (this setting is implied by single, double, quad and high density).
perp=1
Use "perpendicular" sector headers (this setting is implied by extra-density)
gap=value
Sets the size of the read/write gap. I don't know the purpose of this parameter (which is passed as-is to the floppy controller): any value seems to work with any format...
fmt_gap=value
Sets the size of the formatting gap. This is only used by the now obsolete fdformat program, and not by superformat.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

4.3 The media description dictionary in /etc/fdmediaprm

`/usr/local/etc/fdmediaprm' (2) contains a dictionary of commonly used media descriptions. Each description is identified by a name, which can then be used by setfdprm or superformat to refer to it, instead of an explicit description.

Each definition starts with "name":, followed by the actual description. Definitions may be spread over several lines, for better readability. The file may contain comments, which start with # and stop at the end of the line.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

5. Drive descriptions

Unlike earlyer version, fdutils-5.0 separates drive descriptions and media description. For more details on this separation, see section 4.1 Introduction. Drive descriptions are used to describe the hardware characteristics of a drive, such as their maximal density, their rotation speed, their form factor, etc.

5.1 Syntax  What to put into a drive description
5.2 The drive definition file in `/usr/local/etc/fddriveprm'  Where drive definitions are stored


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

5.1 Syntax

A drive description is a series of variable=value and selector clauses.

5.1.1 Density  The maximal available density on the drive
5.1.2 Form factor  Whether this drive is a 3 1/2", 5 1/4" or 8" drive
5.1.3 Cmos code  Sums up both density and form factor
5.1.4 Other parameters  Rotation speed and tracks per inch


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

5.1.1 Density

The density of a drive is the highest media density that it supports. Density is one of sd, dd, qd, hd or ed. Usually, you do not need to specify this parameter, as it can be derived from the drives CMOS code.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

5.1.2 Form factor

The form factor of a drive describes the physical dimensions of the media it accepts. It is one of 3.5, 5.25 or 8. Usually, you do not need to specify this parameter, as it can be derived from the drives CMOS code.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

5.1.3 Cmos code

The PC Bios already knows on its own about the most common drive types. These are named by an integer from 1 to 6, according to the following table.
 
0        no drive installed
1        5.25 DD
2        5.25 HD
3        3.5 DD
4        3.5 HD
5        3.5 ED
6        3.5 ED

As you see 3.5 ED drives have two possible codes. Some BIOSes use 5, others use 6. The reason for this is that initially 5 was intended for floppy tape drives, and only 6 was for 3.5 ED drives. However, some BIOS manufacturers didn't know about this convention, and used 5 for the then "new" 3.5 ED drives.

Usually, you do not need to specify this parameter, as it can be read from the physical CMOS of your PC. This parameter may be useful if your BIOS does not store the drive's CMOS code at the expected place, or if you have more than two drives.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

5.1.4 Other parameters

deviation=deviation
Tells how much more/less raw capacity the drive has than the standard. Due to slightly different rotation speeds (3) and to slightly different data transfer rates, the raw capacity per track can vary slightly. For normal formats, these small deviations from the prescribed raw capacity is not harmful, as these have plenty of safety margins built in. However, the new extra capacity formats are affected by this, as they try to squeeze every available raw byte out of the disk.

Deviation is expressed in ppm. Positive values mean a higher raw capacity than normal, and negative values mean a lower raw capacity than normal. The deviation can be measured using the floppymeter program.

rpm=rotation_speed

Prescribed rotation speed of the drive, expressed in rotations per minute. This is 360 for 5 1/4 HD drives, and 300 for all other commonly available drive types. Usually, you do not need to specify this parameter, as it can be derived from the drive's CMOS code. It is useful however for single density drives or other drives not commonly found on a PC. Usually, you do not to specify this parameter, as it can be derived from the drive's form factor and maximal density.

tpi=cylinder_density

This parameter is only meaningful for 5 1/4 drives. It expresses whether the drive is able to use 80 tracks (tpi=96) or only 40 (tpi=48). Usually, you do not to specify this parameter, as it can be derived from the drive's maximal density: quad density and high density drives are 96 tpi, whereas double density drives are 48 tpi.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

5.2 The drive definition file in `/usr/local/etc/fddriveprm'

`/usr/local/etc/fddriveprm' (4) contains a dictionary of commonly used media descriptions. Each description is identified by a name, which can then be used by setfdprm or superformat to refer to it, instead of an explicit description.

Each definition starts with "drivenumber":, followed by the actual description. Definitions may be spread over several lines, for better readability. The file may contain comments, which start with # and stop at the end of the line.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6. Storing more data on a floppy disk

This section describes the techniques that are used by Linux' floppy driver and superformat to store more data than usual on a floppy disk.

Each section contains a description of the technique used, lists the usages of the disks formatted using this technique (whether they are bootable, whether they are accessible on MS-DOS and for which kind of filesystems they are suitable) and finishes with a table listing the most interesting formats which can be obtained by the described technique.

The table lists for each format the media type it is used for, the total capacity which can be achieved, the throughput for large reads or writes and the media description for these disks. This description can the be used with superformat to make such disks, or with setfdprm to configure the drive to read/write to them. Some formats (the XDF and XXDF formats) cannot be accessed directly, and thus there is no media description for them. For these, we indicate a formatting command used to make these disks. The formatting command assume that the disk is in the first drive (/dev/fd0). Substitute /dev/fd1 if you want to format XDF or XXDF disks in the second drive.

6.1 More sectors per cylinder  Using more sectors per track by packing them close together
6.2 Using interleave  Use interleave to pack the sectors even closer together
6.3 Sector skewing  Speeding up multi-track reads
6.4 More Cylinders  Use up to 83 cylinders
6.5 Larger sectors  Minimize per byte overhead by using larger sectors
6.6 Mixed sector size (MSS) formats  Minimize slack by using several sector sizes in a same track
6.7 Smart use of the data transfer rate  How to get more out of your disk by playing games with the data transfer rate
6.8 2M formats  Make autodetection easyer by using a readable first track
6.9 XDF formats  Fast high capacity formats
6.10 XXDF formats  Fast formats with even higher capacity


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6.1 More sectors per cylinder

The official formats used by MS-DOS and other operating systems are generally very conservative. It is often possible to fit more sectors on each track than the default by simply reducing the size of the gap between tracks and/or the size of the leftover space at the end of the disk.

For example, a 3 1/2 disk has a raw track capacity of around 12500 bytes. The raw capacity of a floppy disk is not rigorously constant among different boxes, because both the data transfer rate of the floppy controller, and the rotation speed of the drive are subject to small variations. In order to account for these, we have to use a safety margin, and we only use up 12450 bytes of the 12500 bytes that are theoretically available.

A sector contains a header of 62 bytes and 512 bytes of data. A minimum gap of about 45 bytes should be used in order to leave enough time to the floppy controller to "rest" between reading two successive sectors. In total, 619 bytes per sector are thus needed.

This shows that we can fit 12450 / 619 = 20 sectors per track.

Usage: These disks are bootable by Lilo, and can be read in MS-DOS using numerous shareware utilities such as vgacopy, or fdformat or many others. Check your nearest Simtel mirror.

With dos6, you don't need any add-on utilities, just put the following line in your config.sys:

 
drivparm=/d:0 /f:7 /h:2 /s:21 /t:82
            ^    ^ \______________/
            |    |          |
   drive number  |     max geometry
                 |
      drive type, consult the dos help system for details

Interesting Formats:

 
density     tot. cap.    throughput    media description
5 1/4 DD     800KB        30KB/s       dd sect=10
3 1/2 DD     800KB        25KB/s       dd sect=10
3 1/2 HD    1600KB        50KB/s       hd sect=21 
3 1/2 ED    3200KB       100KB/s       ed sect=42 

The --dd, --hd and --ed options describe the density of the media to be formatted (double density, high density or extra density).

The -s options describes the number of 512 byte sectors per track.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6.2 Using interleave

After having read a sector, the floppy controller needs to "rest" for a short time. This time is used to compute checksums, to reset internal circuitry, etc. During this time, the floppy disk continues to rotate, and the "rest" time thusly translates to a certain minimal gap size. If a smaller gap is used, the next sector header flies by the read-write head before the floppy controller is ready again to pick up the data. Thus, it has to wait until the next disk rotation until that sector comes back again. This leads to an unacceptably low throughput, as now the system can only read one sector per rotation instead of all sectors in one rotation. If we want to use smaller gaps, we have thus to use sector interleaving. This technique consists in arranging the sectors in a way such that the next logical sector does not immediately follow the current sector, but instead another sector is inserted between two successive sectors. Instead of having the following order:
 
1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21

we would use the following order:

 
1,12,2,13,3,14,4,15,5,16,6,17,7,18,8,19,9,20,10,21,11,

This new order allows the floppy controller to rest during the whole time that sector 12 flies by between reading sector 1 and 2. This technique still cuts throughput in half, because two rotations are needed (one for reading sectors 1 to 11, and the second to read sectors 12 to 21). However, this is far better than the 21 rotations which would be needed without interleave.

This technique allows us to use a gap size of just 1, and thus fit 21 sectors on one track.

Usage: Once formatted, interleaved disks can be used in a similar way to disks which have simply more tracks. They can be accessed using vgacopy in Dos, you can boot from them using Lilo, and you may install any filesystem on them.

Interesting Formats:

 
density     tot. cap.    throughput    media description
5 1/4 HD    1440KB        27KB/s       hd sect=18 
3 1/2 HD    1680KB        26KB/s       hd sect=21 
3 1/2 ED    3360KB        52KB/s       ed sect=42 

You don't need to tell superformat to use interleaving, it figures out by itself when interleaving is needed. You don't need to tell setfdprm either that a disk is interleaved, as this information is not needed to read the disk


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6.3 Sector skewing

Sector skewing is a technique that allows bigger throughputs. It does not increase the capacity of the disk. Sector skewing is only relevant during formatting. Sector skewed disks are indistinguishable from non-skewed disk by software, except for a different throughput.

The principle of sector skewing is to start each track a little bit later than the previous one, i.e. the first logical sector of the second cylinder would for exemple lie near the sixth logical sector of the first cylinder. This is done in order to account for the time needed to seek the drive head from the first cylinder to the second. Without skewing, the first sector would already have passed the drive head after seeking, and we would need to wait for a whole rotation for it to come back again.

By default, superformat applies appropriate skewing to all formats, and the listed throughput values refer to skewed disks. It is possible to provide different values for the skew using the --head_skew and --track_skew parameters. head_skew refers to the offset between both sides of the same cylinder, and track_skew refers to the offset of two consecutive cylinders. 0 means no skew.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6.4 More Cylinders

Many nominally 40-cylinders or 80-cylinder drives are capable of more cylinders, usually 41 and 83 respectively. These can be used to get extra capacity. However, not all drives can seek to these unofficial extra cylinders, and even on drives which can, these extra cylinders tend to be less reliable.

WARNING: Although most drives are able to use 83 cylinders, some may not. If your drive is making strange noises while accessing these tracks.

Although most drives support more than 80 tracks, I have heard rumors that some do not, and repeatedly trying to read beyond track 80 might be damaging to them. In order to know wether your drive supports more than eighty tracks, first set the number of allowed tracks to 82. (using floppycontrol --cylinders 82 -d drive)

Then format a disk with a 82 track format (for example `/dev/fd0H1722'), and copy on or several files to the disk until there are less than 18 KB of free space on the disk. Then eject and reinsert the disk, and compare the files on the disk with the originals. If they are the same, your drive does support 82 tracks. If so, you might want to go further and try with 83 cylinders: `/dev/fd0H1743') This single experience should not damage the drive, although repeating it many times may be dangerous.

If you do have a drive which supports more than 80 cylinders, you have to call floppycontrol --cylinders 82 drive before you can use the extra cylinders. You may put this line into your `/etc/rc.local', so that the driver is automatically configured for the addition cylinder after each boot.

If on the other hand your drive doesn't support more than 80 tracks, you should remove the entries for formats 13-19 from your `/dev' directory after running MAKEFLOPPIES, and you should call floppycontrol --cylinder 80 drive from your `/etc/rc.local' (or floppycontrol --cylinder 40 drive for 5 1/4 DD drives).

By default, 83 cylinder are enabled for any high density and double density drives. 3 1/2 double density drives have 80 cylinders enables, and 5 1/4 double density drives have 40 enabled.

Usage: These disks can be booted from using LILO, and can be accessed in MS-DOS using vgacopy.

Interesting Formats:

All formats presented in the two previous sections may be amended to use 83 cylinders instead of 80. Just add the cyl=83 to the format description for superformat. Using more cylinders has no effect on the throughput.

 
density     tot. cap.    throughput    media description
5 1/4 HD    1494KB        27KB/s       hd sect=18 cyl=83 
3 1/2 HD    1743KB        26KB/s       hd sect=21 cyl=83
3 1/2 ED    3486KB        52KB/s       ed sect=42 cyl=83


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6.5 Larger sectors

The floppy controller allows us to use larger sectors than the default size of 512 bytes. All powers of two larger than 256 bytes are acceptable sector sizes. Large sectors have the same header and gap sizes than smaller sectors, thus the overhead per byte of data is smaller. A little calculation shows this: A 1024 byte sector takes up at least 1024+62+1 = 1087 raw bytes. You can fit eleven sectors of this size into a 12450 byte track. This represents 11KB of data per track, versus the 10.5KB only that can be achieved with 512 byte sectors.

Usage: MS-DOS and other operating systems cannot normally read these formats. Lilo is not yet able to boot from this kind of disks.

Performance: When any portion of one of these larger sectors is read, the entire sector must be read. When any portion of such a sector is written to, the entire sector must be read, and then written back with just the necessary portion modified. Both of these circumstances can entail worse performance than are listed in this table for small reads and (especially) small writes.

Interesting Formats:

 
density     tot. cap.    throughput  media description
5 1/4 HD    1440KB        30KB/s     dd sect=9 ssize=1KB
3 1/2 HD    1760KB        55KB/s     hd sect=11 ssize=1KB
3 1/2 ED    3520KB       110KB/s     ed sect=11 ssize=2KB

The ssize parameter of the format description indicates the sector size to be used.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6.6 Mixed sector size (MSS) formats

Using larger sectors has the disadvantage that the granularity is larger. For example, when using 4096 byte sectors, there is enough space to fit two sectors in a track of 12450 bytes raw capacity, but not three. However, the two sector format leaves plenty of space available (4132 bytes), in which smaller sectors would fit. For example, these 4142 raw bytes can be put to good use by filling them with a 2 KB sector (2048+62), plus an 1 KB sector (1024+62) and a 512 byte sector, leaving still 362 bytes for gaps.

Mixed sector size formats take advantage of this by using sectors of several different sizes on a same track. This way, a maximum capacity of 12KB per track, distributed in one 8k sector and one 4k sector can be achieved.

Usage: There is no known MS-DOS utility which can read basic MSS disks. Lilo is not yet able to boot from this kind of disks.

Performance: As any format with larger sectors, the performance for small reads and writes is worse due to the larger granularity.

Interesting Formats:

 
density     tot. cap.    throughput    media description
3 1/2 DD     880KB        28KB/s       hd tracksize=11b mss
5 1/4 HD    1600KB        30KB/s       hd tracksize=10KB mss
3 1/2 DD     880KB        28KB/s       hd tracksize=11b mss
3 1/2 HD    1840KB        28KB/s       hd tracksize=23b mss
3 1/2 HD    1920KB        30KB/s       hd tracksize=12KB mss
3 1/2 ED    3680KB        56KB/s       ed tracksize=23KB mss
3 1/2 ED    3840KB        60KB/s       ed tracksize=24KB mss

For MSS formats, the system figures out the most efficient repartition of sector sizes by itself. You do not need to describe the number of sectors and their size. For MSS disks, the capacity of one track is described directly, using the tracksize parameter.

The 1920KB and 3840KB formats may be unreliable on some computers.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6.7 Smart use of the data transfer rate

Due to different drive rotations speeds, 5 1/4 double density disks and 3 1/2 double density disks are accessed using different raw data transfer rates (300 kb/s for the faster spinning 5 1/4 disks, and only 250 kb/s for the slower spinning 3 1/2 disks). The method described in this section consists in using the faster data transfer rate intended for 5 1/4 disks on 3 1/2 disks, and thus boost the raw capacity per track of these disks. This is possible because 300 kb/s is still low enough not to excede the specification of the disk surface of a double density disk (which 500 kb/s would).

Usage: this method is only available for 3 1/2 double density disks. The disk obtained cannot be booted from by LILO, and are inaccessible from MS-DOS.

The following table shows the media description for a format using this method in conjuncion with the previous methods:
 
density     tot. cap.    throughput    media description
3 1/2 DD     1120KB         17KB/s     qd tracksize=7KB mss

We use the QD density selector to describe this particular DTR set-up, although the acronym QD is already taken to name 96tpi double density 5 1/4 disks. However, as this dtr trickery is only meaningful for 3 1/2, we hope that there will be no ambiguity.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6.8 2M formats

2M formats use a standard geometry (18 normal sized sectors) on the first side of the first cylinder, and an MSS geometry on the rest of the disk. They are inspired for Ciriaco Garcia de Celis' 2M utility for MS-DOS.

The advantage of 2M disks over simple MSS disks is twofold:

Although 2m disk have less sectors on the first track than on the others, the Linux floppy driver, and 2M's low level floppy access routines pretend that it contains the same number of sectors. The missing sectors are called phantom sectors. Writes to these sectors are ignored, and reads return random data. In order to make up for this, 2M and mtools pretend that there is a duplicate FAT in the missing sectors, which is simulated by using data from the first (real) FAT. Thus 2M disks work fine for their intended purpose, which is to hold an MS-DOS filesystem. Never use 2M disks for anything other than a MS-DOS filesystem. For example, never make an ext2 filesystem on a 2M disk. If you need a high capacity ext2 filesystem (or minix fs, raw tar or cpio archive), use the corresponding MSS format instead

Usage: 2M disks are not bootable by LILO. They can be accessed in MS-DOS using the 2M utility. 2M can be found at ftp://FTP.Coast.NET/SimTel/msdos/diskutil/2m30.zip or at any other simtel mirror. 2M disks are not suitable for non MS-DOS filesystems.

Performance: Just as with MSS disks, performance is bad for small reads and writes.

To describe a 2M format, add the keyword 2m to its media description:
 
density     tot. cap.    throughput    media description
3 1/2 HD    1840KB        28KB/s       hd tracksize=23b mss 2m


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6.9 XDF formats

XDF is the format used for OS/2 installation floppies.

Just like 2M, XDF uses mixed sector sizes on "generic tracks". The first cylinder uses 512 byte sectors.

However, for XDF disks, the logical order of the sectors on a given track, and their physical order is not the same. This allows a faster access, in a similar way that interleaving does for disk with normal sized sectors and too small gaps. XDF's sector arrangement allows it to read sectors alternatively from both sides, i.e. the first sector from side 0, the second from side 1, and the third from side 0 again. This differs from the usualy formats, where first the entire side 0 is read, and then the entire side 1. This technique allows to read both sides of a disk in roughly three rotations.

The following example illustrates how this is done. In our example we use the XDF format used for 3 1/2 HD disks, which contains one 8KB sector, one 2KB sector, one 1KB sector, and one 512 byte sector per track. The upper line represents the sectors on side 0, and the lower line represents the sectors on side 1. Different numbers represent different sectors. Repeated identical numbers represent a single larger sector. As the disk is circular, some sectors wrap around at the end: we find parts of the 8KB sector, represented by 6, both at the beginning and at the end of each track.

 
position:|          1         2         5         4
         | 1234567890123456789012345678901234567890
         |==========================================
side 0:  | 6633332244444446666666666666666666666666
side 1:  | 6666444444422333366666666666666666666666

2   512 byte sector
3   1KB sector
4   2KB sector
6   8KB sector

When reading a track, sectors are read in the following order:
 
sector id    head    position at start     position at end
----------------------------------------------------------
    3          0               3                 7
    4          0               9                16
    6          1              18                 5    (1st wrap around)
    2          0               7                 9
    2          1              12                14
    6          0              16                 3    (2nd wrap around)
    4          1               5                12
    3          1              14                18

We notice that the start of each sector happens at least 2 units of position (around 300 bytes), after the end of the previously read sector, thus allowing the floppy disk controller sufficient time to rest. Moreover, we notice two wrap-arounds, yielding three rotations to read the whole cylinder (the third rotation is due to the fact that we stop at a higher position than we started, and that we also need to allow some time for seeking to the next track).

MSS or 2M formats of the same capacity nead at least 2 rotations per side (i.e. 4 per track), yielding a lower throughput.

Usage: XDF disks are not bootable by LILO. They can be accessed from MS-DOS and OS/2 using xdfcopy.exe or xdf.com. They are only suitable for MS-DOS filesystems. The floppy driver has no direct support for this format yet, but mtools is able to read them using the FDRAWCMD ioctl.

Interesting Formats:

 
density     tot. cap.    throughput    formatting command
5 1/4 HD    1600KB        46KB/s       xdfcopy -0 /dev/fd0
3 1/2 HD    1840KB        38KB/s       xdfcopy -1 /dev/fd0
3 1/2 ED    3840KB       102KB/s       xdfcopy -2 /dev/fd0

The options -1, -2 and -3 descibre one out of the five formats understoood by xdfcopy (3 XDF formats and 2 XDF formats).


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

6.10 XXDF formats

These use the simple principle as XDF, but use a higher geometry. No new principle is used, these formats are simply more daring (smaller gaps, and smaller margin at the end of the sector).

Usage: XXDF disks are not bootable by LILO, and can't be accessed by MS-DOS. They are only suitable for MS-DOS filesystems. The floppy driver has no direct support for this format yet, but mtools is able to read them using the FDRAWCMD ioctl. Due to their smaller tolerances, XXDF formats may not work on all drives. Problems may also occur if you write to XXDF disks using a different drive than the one you used to format the disk.

Interesting Formats:

 
density     tot. cap.    throughput    formatting command
3 1/2 HD    1920KB        45KB/s       xdfcopy -3 /dev/fd0
3 1/2 ED    3840KB        90KB/s       xdfcopy -4 /dev/fd0


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

7. How autodetection works

The principle of autodetection is rather simple. When a floppy disk is first accessed, and its geometry is not yet known, the floppy driver tries out a list of up to 8 geometries (format descriptions) until one is found that matches (i.e. that makes it possible to read the first sector or track). This list of geometries is called the autodetection list. There is one autodetection list per drive type (as indicated in the cmos).

The autodetection list doesn't contain the geometry descriptions themselves, but rather references to entries in the geometry list (see section 3.3 The geometry list). Each list may contain up to 8 such references. Each reference can be tagged with a t flag. If this tag is set, the floppy driver tries to read the whole track when trying out that description; if it is not set, it only tries to read the boot sector.

Reading the whole track is useful to distinguish among geometries which differ only in the amount of sectors per track. In order to do this, put the geometry with the most sectors first in the list, and set its t tag. Use the t tag only in this case, as it makes autodetection slower.

Autodetection cannot distinguish between geometries that only differ in the number of heads or in the number of tracks.

Autodetection is meant to supply only a first approximation of the actual format of the disk. It supplies enough information to enable a program such as mtools to read the boot sector, which contains the exact information. Mtools then uses the information contained in the boot sector to set the exact geometry.

The autodetection list is set using the following command:
 
floppycontrol --autodetect list


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

7.1 Example

The following example restores the default autodetection sequence for a 3 1/2 ED drive:

 
floppycontrol --autodetect 7,8,4,25,28,22,31,21

The following example changes this sequence, so as to add the 1680KB format (number 11). As only 8 formats are allowed in the autodetection list, we have to dump one entry (we chose the last, which is numbered 21). The 1680KB format is identical with the default 1440KB format except for the number of sectors. Thus we must read the whole track in order to distinguish it from the 18 sector format (t flag). Furthermore, the the 1680KB sector format should be detected first, as an 21 sector disk would also matches the standard format with its 18 sectors.

 
floppycontrol --autodetect 11t,7,8,4,25,28,22,31

The following example attempts to autodetect CBM 1581 disks along with the more usual formats. CBM 1581 disks are not among the predefined formats. Thus we first have to pick one of the predefined formats and change it so it fits our needs. We may for example pick one of the rarely used 5 1/4 formats, such as h880, which bears number 20). We first make a device node bearing the requested number (so that we have a filename to pass to setfdprm), then we chmod it so it becomes accessible to mortal users, finally we configure the geometry of the new node, and enter it into the autodetection list. We place it at the 4th position, just behind the usual ED, HD and DD formats, and before the more exotic extended formats. Indeed, formats which are nearer to the head of the list are autodetected faster, and hence more commonly used formats should be put nearer to the beginning (5).

 
mknod /dev/fd0cbm1581 b 2 80
chmod 666 /dev/fd0cbm1581
setfdprm /dev/fd0cbm1581 DD DS sect=10 cyl=80 ssize=512 fmt_gap=35 gap=12 swapsides
floppycontrol --autodetect 7,8,4,20,25,28,22,31

Some formats use more than 80 tracks. It is not possible for the kernel to autodetect the number of tracks in a reasonable time, so you have to use a sufficiently recent version of mtools to set the number of tracks according to the boot sector of the disk. Mtools 3.0 and up are ok. This doesn't obviously work with disks containing something else than a MS-DOS filesystem.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

8. Configuring the floppy driver via lilo or insmod

The floppy driver is configured using the floppy= options in lilo. These options can be typed at the boot prompt, or entered in the lilo configuration file.

Example: If your kernel is called linux-2.0, type the following line at the lilo boot prompt (if you have a thinkpad):
 
linux-2.0 floppy=thinkpad
You may also enter the following line in `/etc/lilo.conf', in the description of linux-2.0:
 
append = "floppy=thinkpad"

Several floppy related options may be given, example:
 
linux-2.0 floppy=daring floppy=two_fdc
append = "floppy=daring floppy=two_fdc"

If you give options both in the lilo config file and on the boot prompt, the option strings of both places are concatenated, the boot prompt options coming last. That's why there are also options to restore the default behaviour.

If you use the floppy driver as a module, use the following syntax: insmod floppy 'floppy="options"'. (This line may be unreadable in the info version of this document. If so, please refer to the printed version).

Example:
 
insmod floppy 'floppy="daring two_fdc"'

Note that in this case floppy= should only be typed out once, and not once for each option. You need at least modules-1.3.57 for this method. However, the older environment variable based syntax is still available:

Bourne (sh, bash, ksh, zsh) syntax:
floppy="daring two_fdc" insmod floppy
C-shell (csh, tcsh) syntax:
setenv floppy "daring two_fdc" ; insmod floppy

Some versions of insmod are buggy in one way or another. If you have any problems (options not being passed correctly, segfaults during insmod), first check whether there is a more recent version. If there isn't, use the old method using environment variables. Problems with insmod happen mostly for options involving both a number and a string, such as floppy=0,4,cmos. Options only involving strings, such as floppy=daring are not affected.

The floppy related options include:

floppy=daring
Tells the floppy driver that you have a well behaved floppy controller. This allows more efficient and smoother operation, but may fail on certain controllers.

floppy=0,daring
Tells the floppy driver that your floppy controller should be used with caution.

floppy=one_fdc
Tells the floppy driver that you have only floppy controller (default)

floppy=two_fdc
floppy=address,two_fdc
Tells the floppy driver that you have two floppy controllers. The second floppy controller is assumed to be at address. If address is not given, 0x370 is assumed. two_fdc is implied if you use the cmos option with a drive of id 4 to 7.

floppy=thinkpad
Tells the floppy driver that you have a Thinkpad. Thinkpads use an inverted convention for the disk change line.

floppy=0,thinkpad
Tells the floppy driver that you don't have a Thinkpad.

floppy=omnibook
floppy=nodma

Tells the floppy driver not to use Dma for data transfers. This is needed for instance on some HP Omnibooks, which don't have a workable DMA channel for the floppy driver. This option is also useful if you frequently get "Unable to allocate DMA memory" messages. Indeed, dma memory needs to be continuous in physical memory, and is thus harder to find, whereas non-dma buffers may be allocated in virtual memory. However, I advise against this if you have an FDC without a FIFO (8272A or 82072). 82072A and later are OK. You also need at least a 486 to use nodma. If you use nodma mode, I suggest you also set the FIFO threshold to 10 or lower, in order to limit the number of data transfer interrupts.

floppy=dma
Tells the floppy driver that a workable DMA channel is available (the default).

floppy=nofifo
Disables the FIFO entirely. This is needed if you get "Bus master arbitration error" messages from your ethernet card (or from other devices) while accessing the floppy.

floppy=fifo
Enables the FIFO (default)

floppy=threshold,fifo_depth
Sets the FIFO threshold. This is mostly relevant in DMA mode. If this is higher, the floppy driver tolerates more interrupt latency, but it triggers more interrupts (i.e. it imposes more load on the rest of the system). If this is lower, the interrupt latency should be lower too (faster processor). The benefit of a lower threshold is less interrupts.

To tune the fifo threshold, switch on over/underrun messages using floppycontrol --messages. Then access a floppy disk. If you get a huge amount of Over/Underrun - retrying messages, then the fifo threshold is too low. Try with a higher value, until you only get an occasional Over/Underrun. It is a good idea to compile the floppy driver as a module when doing this tuning. Indeed, it allows to try different fifo values without rebooting the machine for each test. Note that you need to do floppycontrol --messages every time you re-insert the module.

Usually, tuning the fifo threshold should not be needed, as the default (0xa) is reasonable.

floppy=drive,type,cmos
Sets the cmos type of drive to type. Additionnaly, this drive is allowed in the bitmask. This is useful if you have more than two floppy drives (only two can be described in the physical cmos), or if your BIOS uses non-standard CMOS types. The CMOS types are:
0
unknown or not installed
1
5 1/4 DD
2
5 1/4 HD
3
3 1/2 DD
4
3 1/2 HD
5
3 1/2 ED
6
3 1/2 ED

Note that there are two valid types for ED drives. This is because 5 was initially chosen to represent floppy tapes, and 6 for ED drives. AMI ignored this, and used 5 for ED drives. That's why the floppy driver handles both) Setting the CMOS to 0 for the first two drives (default) makes the floppy driver read the physical cmos for those drives.

floppy=unexpected_interrupts
Print a warning message when an unexpected interrupt is received (default behaviour)

floppy=no_unexpected_interrupts
floppy=L40SX
Don't print a message when an unexpected interrupt is received. This is needed on IBM L40SX laptops in certain video modes. (There seems to be an interaction between video and floppy. The unexpected interrupts only affect performance, and can safely be ignored.)

floppy=broken_dcl
Don't use the disk change line, but assume that the disk was changed whenever the device node is reopened. Needed on some boxes where the disk change line is broken or unsupported. This should be regarded as a stopgap measure, indeed it makes floppy operation less efficient due to unneeded cache flushings, and slightly more unreliable. Please verify your cable, connection and jumper settings if you have any DCL problems. However, some older drives, and also some Laptops are known not to have a DCL.

floppy=debug

Print debugging messages

floppy=messages

Print informational messages for some operations (disk change notifications, warnings about over and underruns, and about autodetection)

floppy=silent_dcl_clear

Uses a less noisy way to clear the disk change line (which doesn't involve seeks). Implied by daring.

(There are other options as well, but they are considered obsolete, and thus they are not documented here)


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

9. Floppy ioctls

All these ioctl's may be issued using the floppycontrol program. (See also floppycontrols man page)

FDSETPRM
sets the geometry (number of tracks, heads and sectors, etc) of a drive.
FDDEFPRM
sets the geometry in a permanent way (not cleared after a disk change)
FDGETPRM
read a previously set drive geometry (or an autodetected geometry) back.
FDCLRPRM
makes the driver forget the geometry for a given drive (to trigger autodetection)
FDFLUSH
forgets the contents of the floppy buffers. CAUTION: This doesn't write dirty buffers to the disk. Use fsync first.
FDGETDRVTYP
displays the type of a drive (name parameter). This is used by MAKEFLOPPIES. For the naming convention, see the description of the MAKEFLOPPIES script. For formats which work in several drive types, FDGETDRVTYP return a name which is appropriate for the oldes drive type which supports this format.
FDSETDRVPRM
sets various drive parameters.
FDGETDRVPRM
reads these parameters back.
FDGETDRVSTAT
gets the cached drive state (disk changed, write protected et al.)
FDPOLLDRVSTAT
polls the drive and return its state.
FDGETFDCSTAT
gets the floppy controller state.
FDRESET
resets the floppy controller under certain conditions.
FDRAWCMD
sends a raw command to the floppy controller.
FDWERRORCLR
clear the write error stats.
FDWERRORGET
gets the write error stats.
FDSETMAXERRS
sets the error thresholds (when to display error messages on the console, and when to abort operations). The maxerror structure is part of the drive parameters, but this ioctl is needed in addition to FDSETDRVPRM because FDSETDRVPRM is only accessible to the superuser whereas FDSETMAXERRS is accessible to whoever has write access to the floppy device.

FDMSGON/FDMSGOFF
switch informational messages on/off. This flag is part of the drive parameters as well, but FDMSGON/FDMSGOFF don't need superuser status.

There are other ioctls as well, but they are considered obsolete and their use is discouraged.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10. Command list

This section describes the available fdutils commands, and the command line parameters that each of them accepts.

10.1 diskd  detect a disk change and execute a command
10.2 diskseekd  seeks the drive from time to time to shake of the dust
10.3 fdmount  automatically mounts and unmounts floppy disks
10.4 fdrawcmd  send raw commands to the floppy disk controller
10.5 floppycontrol  configure the floppy driver
10.6 floppymeter  measures characteristic parameters of a floppy drive
10.7 getfdprm  print current geometry parameters
10.8 makefloppies  makes the floppy device entries
10.10 superformat  formats high capacity disks
10.9 setfdprm  changes the current and permanent geometry parameters
10.11 xdfcopy  copies and formats XDF disks


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.1 diskd

The diskd command has the following syntax:

 
diskd [-d drive] [-i interval] [-e command]

Diskd waits for a disk to be inserted into a given drive, and then either executes the command or exits. This program can be used to automatically mount a disk as soon as it is inserted.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.1.1 Warning

This program works by switching the motor on for a very short interval, and then seeking to track -1. This might damage hardware in the long run. Amigas, which also use these techniques, are known for having problems with their disk drives no longer spinning up properly after a few month of usage.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.1.2 Options

-d drive
Selects the drive to observe for disk insertion. By default, drive 0 (/dev/fd0) is observed.
-i interval
Selects the polling interval. The interval is given in tenths of seconds. Default is 10 (one second).
-e command
Gives the command to be executed when a disk is inserted. If no command is given the program simply exits. Typically, the command mounts the disk. It can be a shell scripts which probes for several filesystems and disk geometries until it succeeds.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.1.3 Bugs


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.2 diskseekd

Several people have noticed that Linux has a bad tendency of killing floppy drives. These failures remained completely mysterious, until somebody noticed that they were due to huge layers of dust accumulating in the floppy drives. This cannot happen under Messy Dos, because this excuse for an operating system is so unstable that it crashes roughly every 20 minutes (actually less if you are running Windows). When rebooting, the BIOS seeks the drive, and by doing this, it shakes the dust out of the drive mechanism. diskseekd simulates this effect by seeking the drive periodically. If it is called as diskseek, the drive is seeked only once.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.2.1 Options

The syntax for diskseekd is as follows:
 
diskseekd [-d drive] [-i interval] [-p pidfile]

-d drive
Selects the drive to seek. By default, drive 0 (`/dev/fd0') is seeked.

-i interval
Selects the cleaning interval, in seconds. If the interval is 0, a single seek is done. This is useful when calling diskseek from a crontab. The default is 1000 seconds (about 16 minutes) for diskseekd and 0 for diskseek.

-p pidfile
Stores the process id of the diskseekd daemon into pidfile instead of the default `/var/run/diskseekd.pid'.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.2.2 Bugs

  1. Other aspects of Messy Dos' flakiness are not simulated.
  2. This section lacks a few smileys.

[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.3 fdmount

 
fdmount [-l] [--list] [-d] [--daemon] [--detach]
[-i interval] [--interval interval] [-o mount-options]
[-r] [-readonly] [-s] [--sync] [--nosync] [--nodev]
[--nosuid] [--noexec] [-f] [--force] [-h] [--help]
[drivename] [mountpoint]

fdumount [-f] [--force] [drivename]

fdlist

fdmountd [-i interval] [--interval interval] [-r]
[-readonly] [-s] [--sync] [--nosync] [--nodev]
[--nosuid] [--noexec] [--help] [drivename] [mountpoint]]

The fdmount program mounts a floppy disk in the specified drive. It tries to figure out the exact format and filesystem type of the disk from data in the disk's boot sector or super block and the auto-detected track layout.

Currently, fdmount supports the filesystems minix, ext, ext2, xia, and msdos, and includes special support for disks formatted by the 2M utility for MS-DOS.

It also checks whether the disk is write protected, in which case it is mounted read-only.

The symbolic drivename is (currently) one of `fd[0-7]', corresponding to the special device files `/dev/fd[0-7]'. If drivename is not specified, `fd0' is assumed.

The disk is mounted on the directory mountpoint, if specified, or on `/fd[0-7]'. In either case, the mount point must be an existing, writable directory.

Due to a bug in the floppy driver (?), the polling interval (-i flag) must be longer than the spindown offset. Thus you need to do (for example) floppycontrol --spindown 99 before starting fdmountd in daemon mode


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.3.1 Options

-l --list
List all known drives with their symbolic name, type, and mount status.

-d --daemon
Run in daemon mode (see below).

--detach
Runs daemon in background, and detaches it from its tty. Messages produced after the fork are logged to syslog.

-p file
--pidfile file

Dumps the process id of the daemon to file. This makes killing the daemon easier: kill -9 `cat file`

-i interval
--interval interval
Set the polling interval for daemon mode. The unit for interval is 0.1 seconds, the default value is 10 (i.e. 1 second).

-o options
--options options
Sets filesystem-specific options. So far, these are only available for DOS and Ext2 disks. The following DOS options are supported: check, conv, dotsOK, debug, fat, quiet, blocksize. The following Ext2 options are supported: check, errors, grpid, bsdgroups, nogrpid, sysvgroups, bsddf, minixdf, resgid, debug, nocheck. When running as a daemon, options not applying to the disk that is inserted (because of its filesystem type) are not passed to mount.

-r --readonly
Mount the disk read-only. This is automatically assumed if the disk is write protected.

-s --sync
Mount with the SYNC option.

--nosync
Mounts without the SYNC option, even when running as daemon.

--nodev
Mount with the NODEV option. Ignored for msdos filesystems, otherwise always set for non-root users.

--nosuid
Mount with the NOSUID option. Ignored for msdos filesystems, otherwise always set for non-root users.

--noexec
Mount with the NOEXEC option.

-f --force
Attempt a mount or unmount operation even `/etc/mtab' says that the drive is already mounted, or not mounted, respectively. This option is useful if `/etc/mtab' got out of sync with the actual state for some reason.

-h --help
Show short parameter description


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.3.2 Security

When mounting on the default mount point, the mount points' owner is set to the current user, and the access flags according to the user's umask. For a specified mountpoint, owner and permissions are left unchanged. Default mount points are called /fd0, /fd1, ... , /fd7.

The user running fdmount must have read access to the floppy device for read only mounts, and read/write access for read/write mounts.

Fdmount can be run suid root, allowing users to mount floppy disks. The following restrictions are placed upon non-root users:

However, do not rely on fdmount being secure at the moment.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.3.3 Daemon mode

In daemon mode, the specified drive is periodically checked and if a disk is inserted, it is automatically mounted.

When the disk is removed, it is automatically unmounted. However, it is recommended to unmount the disk manually before removing it. In order to limit corruption, disks are mounted with the SYNC option when running in daemon mode, unless the --nosync flag is given.

Note that this mode has some potential drawbacks:


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.3.4 Diagnostics

error opening device name

error reading boot/super block
fdmount failed to read the first 1K of the disk. The disk might be damaged, unformatted, or it may have a format wich is unsupported by the FDC or the Linux kernel.

unknown filesystem type
No magic number of any of the supported filesystems (see above) could be identified.

sorry, can't figure out format (fs filesystem)
The size of the filesystem on the disk is incompatible with the track layout detected by the kernel and an integer number of tracks. This may occur if the filesystem uses only part of the disk, or the track layout was detected incorrectly by the kernel.

failed to mount fs> <sizeK-disk
The actual mount system call failed.

failed to unmount
The actual unmount system call failed.

cannot create lock file /etc/mtab~
If `/etc/mtab~' exists, you should probably delete it. Otherwise, check permissions.

Can't access mountpoint
Most probably, the default or specified mount point does not exist. Use mkdir.

mountpoint is not a directory
The mountpoint is not a directory.

not owner of mountpoint
Non-root users must own the directory specified as mount point. (This does not apply for the default mount points, /fd[0-3].)

No write permission to mountpoint
Non-root users must have write permission on the mount point directory.

Not owner of mounted directory: UID=uid
Non-root users cannot unmount if the mount point is owned (i.e. the disk was mounted) by another user.

invalid drive name
Valid drive names are `fd0', `fd1', etc.

drive name does not exist
The drive does not exist physically, is unknown to the Linux kernel, or is an unknown type.

Drive name is mounted already
Trying to mount a drive which appears to be mounted already. Use the --force option if you think this is wrong.

Drive name is not mounted
Trying to unmount a drive which does not appear to be mounted. Use the --force option if you think this is wrong.

ioctl(...) failed
If this occurs with the FDGETDRVTYP or FDGETDRVSTAT, ioctl's you should probably update your Linux kernel.

mounted fs size-disk (options)
Success message.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.3.5 Bugs


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.4 fdrawcmd

 
fdrawcmd [drive=drive] [rate=rate]
[length=length] [repeat=repeat]
[cylinder=physical-cyl] command [paramters ...] [mode]

fdrawcmd is used to send raw commands to the floppy disk controller, after having selected a given drive. You must have write permission to the selected drive.

When writing to a disk, data is read from stdin; when reading, data is printed to stdout. Diagnostic messages, return values from the controller, and the value of the disk change line after the command are printed to stderr.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.4.1 Options

All numbers may be given in octal (0211), decimal (137), or hexadecimal (0x89).

drive=drive
Selects the drive. The default is drive 0 (`/dev/fd0').

rate=rate
Selects the data transfer rate. Use 0 for high density disks, 1 for double density 5 1/4 disks (or 2 Mbps tapes, if the appropriate rate table is selected), and 2 for double density 3 1/2 disks.

length=length
Describes the length of the transferred data for commands reading from and writing to the disk. The default is to continue until end of file.

repeat=count
Repeat the command count times. This only works correctly for commands which don't do any data transfer.

cylinder=count
Seek to the given cylinder before executing the command

command
The name of the command to send. command may be a spelled out name (like read or write), or a number representing the commands floppy disk controller opcode. A named command has already a mode associated with it, whereas for a number the mode parameter should be described using the mode option.

parameters
The parameters for the command (optional, not all commands need parameters).

mode
Various flags or'ed together describing the properties of the command.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.4.2 Commands

The description of the various floppy commands given in this manpage is very sketchy. For more details get the 82078 spec sheet which can be found at:
 
http://www-techdoc.intel.com/docs/periph/fd_contr/datasheets/

Look for the chapter COMMAND SET/DESCRIPTIONS. Older FDCs only support a subset of the commands described therein, but the syntax for the commands that do exist is the same.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.4.2.1 Commands available on all FDCs

read drvsel cyl head sect szcod spt rw-gap szcod2
Reads length bytes of data from the disk. drvsel is the drive selector. Bit 0 and 1 describe the drive, and bit 2 describes the head. The remaining parameters give the cylinder, head (yes, again), sector, size of the sector (128 * 2 ^ szcod), sectors per track (spt, this is used to switch to the second head when the first side has been read), and size of the read-write gap. szcod2 should be 0xff. read returns ST0 ST1 ST2 and cyl head sect szcod of the next sector to be read; see `/usr/include/linux/fdreg.h' .

N.B. Certain newer floppy disk controllers are buggy, and do not correctly recognize the end of transfer when operating in virtual DMA mode. For these, you need to set spt to the id of the last sector to be read (for example, if you intend to read sectors 2, 3, 4, set spt to 4, even if the disk has more sectors), and set the no-mt flag.

write drvsel cyl head sect szcod spt rw-gap szcod2
Analogous to read.

sense drvsel
Returns the third status byte (ST3)

recalibrate drvsel
Recalibrates the drive and returns ST0 ST1.

seek drvsel cyl
Moves the head to cyl and returns ST0 ST1.

specify drvsel spec1 spec2
Specify various parameters to the drive.

format drvsel szcod sect-per-track fmt-gap fmt-fill
Formats the cylinder. The new sectors are filled with fmt-fill. The header information comes from the input, which is made up of cyl head sect szcod quadruples. The szcod parameter from the command line is used to describe the actual size of the sectors, and the szcod from the input is used to write into the header. However, the first write to these sectors will use the header information, and might overwrite the following sectors if the szcod parameter from the command line was too small.

readid drvsel
reads the first sector header that comes and returns ST0 ST1 ST2 and cyl head sect szcod of the encountered header.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.4.2.2 Commands available on 82072 and later

dumpregs
Prints the contents of the FDCs registers, if supported.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.4.2.3 Commands available on 82072A and later

configure conf1 conf2 conf3
Configures FIFO operation.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.4.2.4 Commands available on 82077 and later

version
Echoes 0x90 if the FDC is more recent than 82072A, and 0x80 otherwise

perpendicular rate
Sets the perpendicular mode. Use 0 for normal, 2 for 500kb/s perpendicular, and 3 for 1 Mb/s perpendicular.

seek-out drvsel n
does a relative seek of n cylinders towards cylinder 0.

seek-in drvsel n
does a relative seek of n cylinders away from cylinder 0.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.4.2.5 Commands available on 82077AA and later

lock
Locks the FIFO configuration, so that it survives a FDC software reset.
unlock
Unlock the FIFO configuration


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.4.2.6 Commands available on 82078

partid
echoes a byte describing the type of the FDC in the 3 high bits, and the stepping in the three low bits.

powerdown powerconf
configures automatic power down of the FDC. The old configuration is echoed

option iso
enables/disables ISO formats. Odd values of iso enable these formats, whereas even values disable them. ISO formats don't have index headers, and thus allow to fit slightly more data on a disk.

save
prints out 16 internal registers of the FDC.

restore r1 r2 r3 ... r16
restores the 16 internal registers of the FDC.

format_n_write drvsel szcod sect-per-track fmt-gap fmt-fill
formats the cylinder and writes initial data to it. The input data is made up of a sequence of headers (4 bytes) and data: header1 data1 header2 data2 ... headern datan

drivespec dspec1 dspec2 ... specn terminator
chooses rate tables for various drives. Each dspec byte describes one drive. Bits 0 and 1 say which drive is described. Bits 2 and 3 describe the rate table. Only tables 0 and 2 are interesting. Both tables only differ in the meaning og rate 1. For table 0 (the default) rate 0 is 300 kb/s (used for 5 1/4 DD disks), whereas for table 1 it is 2 Mbps (used for fast floppy tape drives). Bit 4 is the precompensation table select bit. It should be set to 0. Bit 5-7 should be zero as well. The terminator byte ends the drivespec command. It is either 0xc0 or 0x80. If it is 0xc0, no result phase follows; if it is 0x80, the current data rate table configuration for the four drives is echoed.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.4.3 Modes

The mode option is only needed when you describe the command as a numerical value. Some mode names are also valid command names. They are considered as command name if the command name has not yet been given, and as mode name otherwise.

If you give a command name followed by explicit modes, both the implicit flags of the command name, and the explicit modes are or'ed together.

If on the other hand you give a command name preceded by explicit modes, only the explicit modes are or'ed together.

read
Read data from disk using DMA.

write
Write data to the disk.

intr
Wait for an interrupt.

spin
wait for the disk to spin up

disk
Aborts the operation if no disk is in the drive. This only works if you also chose a physical cylinder to seek to.

no-motor
Don't switch on the drive motor while issuing the command

no-motor-after
Switch off the motor immediately after the command returns.

fm
Uses the FM version of the read, readid, write and format commands.

no-mt
Do not use MT (multitrack) mode for the read, readid and write commands. This is needed on certain broken FDC's which don't recognize end of transfer when running in nodma mode. In order to use these safely, set no-mt, and chose the id of the last sector to be read as sect-per-track.

fdrawcmd opens the device node with the NDELAY flag. This means that the driver should not try to autodetect the disk type (it might not be formatted), and that it should not reset the FDC. If a reset was needed, the command simply fails. If that happens, execute floppycontrol --resetnow 0 , and try again.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5 floppycontrol

 
floppycontrol [-p] [--pollstate] [--printfdstate]
[-a operation-abort-threshold] [-c read-track-threshold]
[-r recalibrate-threshold] [-R reset-threshold]
[-e reporting-threshold] [-f] [-x] [-d drive][-F] [-T]
[-reset condition] [--debug] [--nodebug] [--messages]
[--nomessages] [--broken_dcl] [--working_dcl] [--inverted_dcl]
[--no_inverted_dcl] [--silent_dcl_clear] [--noisy_dcl_clear]
[-ccmos-type] [-hlt hlt] [-hut hut] [-srt srt] [-o spindown]
[-u spinup] [-s select-delay] [-rps rotations-per-second]
[-O spindown-offset] [-track max-tracks] [-timeout seconds]
[-C check-interval] [-n native-format]
[-autodetect autodetection-sequence] [-P] [--clrwerror]
[--printwerror] [-h]

The floppycontrol program is used to configure the floppy driver.

10.5.1 General Options  General purpose options
10.5.2 One time actions  Perform various actions
10.5.3 Printing current settings  Print out current configuration
10.5.4 Drive type configuration and autodetection  Do you have a 3 1/2 double density drive or a 5 1/4 high density drive?
10.5.5 Configuration of the disk change line  Disk change line configuration.
10.5.6 Timing Parameters  Change the timings of various operations
10.5.7 Debugging messages  Switching debugging messages on/off
10.5.8 Error Handling Options  How should the floppy driver react when encountering disk errors
10.5.9 Write error reporting  gather statistics about write errors
10.5.10 Other drive configuration options  Other configuration options


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5.1 General Options

-h
--help
Print a help screen.

-d drive
--drive drive
Selects the drive to configure. The default is drive 0 (`/dev/fd0').


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5.2 One time actions

The following floppycontrol options don't set a configuration parameter, but perform a one-time action. They are available to anybody who has write access to the drive

-f
--flush
Flushes (throws away) the dirty data buffers associated with this drive.
-x
--eject
Ejects the disk out of the drive (Sparc). The dirty buffers are first committed to disk before ejecting it. Fails if the disk is mounted.

--reset condition
Resets the FDC under condition . Condition may be one of the following:
0
resets the FDC only if a reset is needed anyways,
1
resets the FDC also if a raw command has been performed since the last reset, and
2
resets the FDC unconditionally.

This command may be needed after some failed raw commands (see section 10.4 fdrawcmd).

-F
--formatend
Issues an end format ioctl. This might be needed after exiting a fdformat in an unclean way. superformat is not subject to this.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5.3 Printing current settings

-T
--type
Print out the drive name of a floppy device. This is used by the MAKEFLOPPIES script. The drive name is a letter (describing the drive type) followed by the capacity of the format in bytes. The letter is E for 3.5 ED drives, H for 3.5 HD drives, D for 3.5 DD drives, h for 5.25 HD drives and d for 5.25 DD drives. The drive type letter corresponds to the oldest drive type supporting the format of this device node (not necessarily the type of the drive refered by this node.) For the generic format nodes (/dev/fd0 et al.) the name of "native format" of the drive is printed, and for the default formats, if a generic format has been redefined, its name becomes (null).

-p
--print
Prints out the configuration of the drive. The names of the various fields are the same as the names of the option to set them, see below.

-P
--printstate
Prints out the cached internal state of the driver. The first line lists various attributes about the disk:
drive present
disk present
disk writable
These are only updated when the drive is accessed.
spinup
is the time when the motor became switched on for the last time.

select
is the time when the drive became selected for the last time

first_read
is the time when the first read request after the last spin up completed.

probed_fmt
is the the index of the autodetected format in the autodetection sequence for this drive.

cylinder
is the cylinder where the drive head currently sits. If this number is negative, it has the following meaning:
  • -1 means that the driver doesn't know, but the controller does (a seek command must be issued).
  • -2 means that the controller doesn't know either, but is sure that it not beyond the 80th track. The drive needs a recalibration.
  • -3 means that the head may be beyond the 80th track. The drive needs two successive recalibrations, because at each recalibration, the controller only issues 80 move head commands per recalibration.

maxblock
is the highest block number that has been read.
maxcylinder
is a boolean which is set when a sector that is not on cylinder 0/head 0 has been read. These are used for smart invalidation of the buffer cache on geometry change. The buffer cache of the drive is only invalidated on geometry change when this change actually implies that a block that has already been read changes position. This optimization is useful for mtools which changes the geometry after reading the boot sector.

generation
is roughly the number of disk changes noticed since boot. Disk changes are noticed if the disk is actually changed, or if a flush command is issued and for both cases if any I/O to/from the disk occurs. (i.e. if you insert several disks, but don't do any I/O to them, the generation number stays the same.)

refs
is number of open file descriptors for this drive. It is always at least one, because floppycontrol's file descriptor is counted too.

device
is format type (as derived from the minor device number) which is currently being used.

last_checked
is date (in jiffies) when the drive was last checked for a disk change, and a disk was actually in the drive.

--pollstate
Polls the drive and then prints out the internal state of the driver.(--Printstate only prints out the cached information without actually polling the drive for a disk change.)

--printfdcstate
Prints out the state of the controller where the target drive is attached to.
spec1
spec2
are the current values of those registers.

rate
is current data transfer rate

rawcmd
is true if a raw command has been executed since the last reset. If this is the case, a reset will be triggered when a drive on the same FDC is next opened.

dor
is the value of the digital output register. The 4 high bits are a bit mask describing which drives are spinning, the 2 low bits describe the selected drive, bit 2 is used to reset the FDC, and bit 3 describes whether this FDC has hold of the interrupt and the DMA. If you have two FDCs, bit 3 is only set on one of them.

version
is the version of the FDC. See `linux/include/linux/fdreg.h' for a listing of the FDC version numbers.

reset
is true if a reset needs to be issued to the FDC before processing the next request.

need_configure
is true if this FDC needs configuration by the FD_CONFIGURE command.

has_fifo
is set if the FDC understands the FD_CONFIGURE command.

perp_mode
describes the perpendicular mode of this FDC. 0 is non-perpendicular mode, 2 is HD perpendicular mode, 3 is ED perpendicular mode, and 1 is unknown.

address
is the address of the first I/O port of the FDC. Normally, this is 0x3f0 for the first FDC and 0x370 for the second.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5.4 Drive type configuration and autodetection

The following options handle the different available drive types, such as double density vs. high density vs. extra density drives, and 5 1/4 drives vs 3 1/2 drives. Usually the drive type is stored in a non-volatile memory, called CMOS, under the form of an integer ranging from 1 to 6.

Different drive types are able to handle and autodetect different formats (different autodetection lists). They also have different "native format name". The native format is the "usual" format with the highest capacity supported by the drive. (For example 720KB on a double density 3 1/2 drive, and 1.2MB on a high density 5 1/4 drive.)

These settings are only changeable by the super user.

-c cmos-type
--cmos cmos-type
Set the virtual CMOS type of the floppy drive. This is useful if Right now, this CMOS parameter is not used by the kernel, except for feeding it back to other applications (for instance superformat, floppymeter or MAKEFLOPPIES). It is also possible to supply a virtual CMOS type with the cmos boot option (see section 8. Configuring the floppy driver via lilo or insmod). If possible, I recommend you use the boot option, rather than floppycontrol, because the boot option also sets any parameters derived from the CMOS type, such as the autodetection list and the native format, whereas floppycontrol does not.

-A autodetect-seq
--autodetect autodetect-seq
Set the autodetection sequence (see section 7. How autodetection works) The autodetection sequence is a comma-separated list of at most eight format descriptors. Each format descriptor is a format number optionally followed by the letter t. For drive 0, the format number is the minor device number divided by 4. The autodetection sequence is used by the driver to find out the format of a newly inserted disk. The formats are tried one after the other, and the first matching format is retained. To test the format, the driver tries to read the first sector on the first track on the first head when t is not given, or the whole first track when t is given. Thus, autodetection cannot detect the number of tracks. However, this information is contained in the boot sector, which is now accessible. The boot sector can then be used by mtools to configure the correct number of tracks.

Example:
 
7,4,24t,25
means to try out the formats whose minor device numbers are 28 (1.44M), 16 (720KB), 96 (1.76MB), and 100 (1.92MB), in this order. For the 1.76MB format, try to read the whole track at once.

Reading the whole track at once allows you to distinguish between two formats which differ only in the number of sectors. (The format with the most sectors must be tried first.) If you use mtools(6), you do not need this feature, as mtools can figure out the number of sectors without any help from the floppy driver, by looking at the boot sector.

Reading the whole track at once may also speed up the first read by 200 milliseconds. However, if, on the other hand, you try to read a disk which has less sectors than the format, you lose some time.

I suggest that you put the most often used format in the first place (barring other constraints), as each format that is tried out takes 400 milliseconds.

-n native-format
--native_format native-format
Set the native format of this drive. The native format of a drive is the highest standard format available for this drive. (Example: For a 5 1/4 HD drive it is the usual 1200K format.) This is format is used to make up the format name for the generic device (which is the name of the native format). This drive name is read back from the kernel by the MAKEFLOPPIES script which uses it to decide which device nodes to create.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5.5 Configuration of the disk change line

--broken_dcl
Assumes that the disk change line of the drive is broken. If this is set, disk changes are assumed to happen whenever the device node is first opened. The physical disk change line is ignored.

This option should be used if disk changes are either not detected at all, or if disk changes are detected when the disk was actually not changed. If this option fixes the problem, I'd recommend that you try to trace the root cause of the problem. Indeed, this options results in reduced performance due to spurious cache flushes.

The following hardware problems may lead to a bad disk change line:

--working_dcl
Assumes that the disk change line works all right. Switching from broken to working may lead to unexpected results after the first disk change.

--inverted_dcl
Assumes that this disk drive uses an inverted disk change line. Apparently this is the case for IBM thinkpads.

--no_inverted_dcl
Assumes that this drive follows the standard convention for the disk change line.

--noisy_dcl_clear
Switches off silent disk change line clearing for this drive.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5.6 Timing Parameters

This section describes how to configure drive timings. To set these parameters, you need superuser privileges. All times are in "jiffy" units (10 milliseconds), unless otherwise specified.

--hlt hlt
Set the head load time (in microseconds) for this floppy drive. The head load time describes how long the floppy controller waits after seeking or changing heads before allowing access to a track.

--hut hut
Set the head unload time (in microseconds) for this floppy drive. The head unload time describes how long the floppy controller waits after an access before directing its attention to the other head, or before seeking.

--srt srt
Set the step rate (in microseconds) for this floppy drive. The step rate describes how long the drive head stays on one cylinder when seeking. Setting this value to low (too fast seeks) may make seeks fail, because the motor doesn't follow fast enough.

-u spinup-time
--spinup spinup-time
Set the spinup time of the floppy drive. In order to do read or write to the floppy disk, it must spin. It takes a certain time for the motor to reach enough speed to read or write. This parameter describes this time. The floppy driver doesn't try to access the drive before the spinup time has elapsed. With modern controllers, you may set this time to zero, as the controller itself enforces the right delay.

-o spindown-time
--spindown spindown-time
Set the spindown time of this floppy drive. The motor is not stopped immediately after the operation completes, because there might be more operations following. The spindown time is the time the driver waits before switching off the motor.

-O spindown-offset
--spindown_offset spindown-offset
Set the spindown offset of this floppy drive. This parameter is used to set the position in which the disk stops. This is useful to minimize the next access time. (If the first sector is just near the head at the very moment at which the disk has reached enough speed, you win 200 milliseconds against the most unfavorable situation).

This is done by clocking the time where the first I/O request completes, and using this time to calculate the current position of the disk.

-s select-delay
--select_delay select-delay
Set the select delay of this floppy drive. This is the delay that the driver waits after selecting the drive and issuing the first command to it. For modern controllers/drives, you may set this to zero.

-C check-interval
--checkfreq check-interval
Set the maximal disk change check interval. The disk change line is checked whenever a read or write to the device is issued, and it has not been checked for more than interval jiffies.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5.7 Debugging messages

This subsection describes how to switch the available debugging messages on and off.

--debug
Switch debugging output on. The debugging information includes timing information. This option might be useful to fine-tune the timing options for your local setups. (But for most normal purposes, the default values are good enough.)

--nodebug
Switch debugging output off.

--messages
Print informational messages after autodetection, geometry parameter clearing and dma over/underruns.

--nomessages
Don't print informational messages after these events.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5.8 Error Handling Options

The following options configure the behavior of the floppy driver in case of read/write errors. They may be used by any user who has write privileges for the drive. Whenever the floppy driver encounters an error, a retry counter is incremented. If the value of this counter gets bigger than the thresholds described below, the corresponding actions are performed at the next retry. The counter is reset when the read or write finally terminates, whether successfully or not.

-a operation-abort-trshld
--abort operation-abort-trshld
Tell the floppy driver to stop trying to read/write a sector after operation-abort-trshld retries, and signal the I/O error to the user.

-t read-track-trshld
--readtrack read-track-trshld
Tell the floppy driver to switch from track-reading mode to sector-at-a-time-mode after read-track-trshld retries.
-r recalibrate-trshld
--recalibrate recalibrate-trshld
Tell the floppy driver to recalibrate the drive after recalibrate-trshld retries.

-R reset-treshold
--reset reset-threshold
Tell the floppy driver to reset the controller after reset-threshold retries. After a controller reset, the floppy driver also recalibrates all drives connected to that controller.

-e error-report-trshld
--reporting error-report-trshld
Tell the floppy driver to start printing error messages to the console after error-report-trshld retries.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5.9 Write error reporting

Due to the buffer cache, write errors cannot always be reported to the writing user program as soon as the write system call returns. Indeed, the actual writing may take place much later. If a write error is encountered, the floppy driver stores information about it in its per drive write error structure. This write error structure stays until explicitly cleared. It can for example be queried by a backup program which wants to make sure that the data has been written successfully.

--clrwerror
Clears the write error structure.

--printwerror
Prints the contents of the write error structure:
write_errors
is a count of how many write errors have occurred since the structure was last cleared.
badness
is the maximal number of retries that were needed to complete an operation (reads, writes and formats).
first_error_sector
is where the first (chronologically) write error occurred.
first_error_generation
is the disk change generation in which did the first write error occurred. The disk change generation is a number which is incremented at each disk change.
last_error_sector
and
last_error_generation
are similar.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.5.10 Other drive configuration options

This subsection lists per drive configuration options, which don't fit in any other category. They are available only to the superuser:

--tracks max-tracks
Set the maximal numbers of physical tracks that this drive may handle. If you have a drive which is only able to handle 80 tracks (making strange noises when you try to format or read a disk with more than 80 tracks), use this option to prevent unprivileged users of damaging your drive by repeatedly reading disks with more than 80 tracks.

If you trust your users and your disks, you don't need this. With most drives you don't need to worry anyways. See section 6.4 More Cylinders, for details.

-i sector-interleave
--interleave sector-interleave
Set the number of sectors beyond which sector interleaving will be used. This option will only be used by the FDFMTTRK ioctl. The fdformat command, which is now considered obsolete, uses FDFMTTRK ioctl, but superformat does not.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.6 floppymeter

 
floppymeter [-f] [-w warmup-delay] [-W window]
[-c cycles] [-h] drive

The floppymeter program measures characteristic parameters of a floppy drive and floppy controller, such as the rotation speed of the drive, the data transfer rate of the controller, and the resulting raw capacity of a disk track. To use this program, insert a disposable floppy in the drive, and type floppymeter --density, where density describes the density of the disk used for the test. (Should be one of dd, hd or ed). CAUTION: the data on the disk will be erased. This program should be used to verify whether the drive and controller are out of tolerance if you experience problems with some high capacity formats. It only needs to be run once per drive: although a disk is needed to perform the measurements, the measured data only depend on the drive and the controller, and not on the disk.

To measure the raw capacity of the disk track, the floppymeter program formats the first track of the drive in a special way that allows it to read the raw data (gaps and headers) of the disk. Thus, all data previously stored on that disk is lost.

The rotation speed is measured by timing the return time of a readid command. In order to gain more precision, the command is issued many times in a row. During this phase, the number of rotations til the start of the test, the average time per rotation til the start, and a sliding average of the times of the last 30 rotations is printed, and updated continously.

The data transfer rate is deduced from the two parameters above.

At the end of the program, all parameters (raw capacity, duration of one rotation, and data transfer rate) are printed again, as well as their relative deviation to the standard value. Finally, it suggests a capacity deviation description line, which can be directly pasted into the drive definition file (See section 5. Drive descriptions.).

Usually, the data transfer rate should not deviate more than 150 ppm from the expected value, and the rotation speed of the drive should not deviate more than 3000 ppm from the expected value. If these deviations are bigger, you may get problems with certain high capacity formats.

If the raw capacity of the drive is too small, some high capacity formats may become unformattable on this drive/controller combo.

If on the other hand, the raw capacity of the drive is too big, you may get problems when writing to a disk formatted by this drive on another drive with a smaller raw capacity. In order to avoid this, increase superformats gap parameter (-G).

-h
Prints a short help

--dd
Tells the program that we use a Double Density disk.

--hd
Tells the program that we use a High Density disk.

--ed
Tells the program that we use an Extra Density disk.

-f
Runs the measurement non interactively. With this option, the program doesn't ask for confirmation, and doesn't display the continously updated values during the rotation speed measurement.

-W Window
This value describes how many rotations are used for the computation of the sliding average. Default is 30.

-c cycles
Describes the number of rotations clocked during the rotations speed determination test. Default is 1000.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.6.1 Bugs

This program is quite new, and may have bugs. Here are a few suggested tests to check its sanity:


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.7 getfdprm

 
getfdprm [drive]

getfdprm prints the current geometry information for drive . This information can be set using setfdprm


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.8 makefloppies

 
MAKEFLOPPIES [-tlvng] [drives]

The MAKEFLOPPIES shell script creates the new floppy block device node. It uses the floppycontrol program to translate the minor device numbers into meaningful names. It also uses these names to decide whether to create a given block device file or not, depending on the type of the physical drive (for instance, for a 3 1/2 drive, the formats corresponding to a 5 1/4 drive are not created).

If you have more than two floppy drives, you need to tell the kernel the CMOS types of those additional drives using the floppy=drive,type,cmos lilo option.

If the drives parameter is given, only the device nodes for the listed drives are made. By default, all only the two first drives are tried.

MAKEFLOPPIES does not work if you redefine your default formats.

Caution: MAKEFLOPPIES removes already existing floppy device nodes.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.8.1 Options

-t
Use the old naming convention for 3 1/2 devices (e.g. `fd0H720' instead of `fd0u720').

-m
Base the name for the created devices on the type of the media (e.g. `fd0h720' instead of `fd0u720').

-l
Local. Creates device nodes in the local directory, not /dev

-v
Verbose

-n
Dry run. (just report what would be done, do not do anything)

-g
Group. Allow read/write access to floppy devices only for group `floppy'


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.8.2 Bugs

The Makefloppies script does not work on redefined "default" formats, If you redefine default formats, you need to create the needed device nodes manually.
[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.9 setfdprm

 
setfdprm [-p] device media-description

setfdprm [-c | -y | -n] device

setfdprm is a utility that can be used to load disk parameters into the auto-detecting floppy devices and "fixed parameter" floppy devices, to clear old parameter sets and to disable or enable diagnostic messages. These parameters are derived from a media-description, see section 4. Media description for more details.

Without any options, setfdprm loads the device (for example `/dev/fd0' or `/dev/fd1') with a new parameter set with the name entry found in `/etc/fdprm' (usually named 360/360, etc.). For autodetecting floppy devices, these parameters stay in effect until the media is changed. For "fixed parameter" devices, they stay in effect until they are changed again.

Setfdprm can also be used by the superuser to redefine the default formats.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.9.1 Options

-p device name
Permanently loads a new parameter set for the specified auto-configuring floppy device for the configuration with name in `/etc/fdprm'. Alternatively, the parameters can be given directly from the command line.

-c device
Clears the parameter set of the specified auto-configuring floppy device.

-y device
Enables format detection messages for the specified auto-configuring floppy device.

-n device
Disables format detection messages for the specified auto-configuring floppy device.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.9.2 Bugs

This documentation is grossly incomplete.
[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.10 superformat

 
superformat [-D dos-drive] [-v verbosity-level] [-b begin-track]
[-e end-track] [--superverify] [--dosverify]
[--noverify] [--verify_later] [--zero-based]
[-G format-gap] [-F final-gap] [-i interleave] [-c chunksize]
[-g gap] [--absolute-skew absolute-skew] [--head-skew head-skew]
[--track-skew track-skew] [--biggest-last] drive [media-description]

superformat is used to format disks with a capacity of up to 1992K HD or 3984K ED. See section 6. Storing more data on a floppy disk, for a detailed description of these formats. See section 4. Media description, for a detailed description of the syntax for the media description. If no media description is given, superformat formats a disk in the highest available density for that drive, using standard parameters (i.e. no extra capacity formats).

When the disk is formatted, superformat automatically invokes mformat in order to put an MS-DOS filesystem on it. You may ignore this filesystem, if you don't need it.

Supeformat allows to format 2m formats. Be aware, however, that these 2m formats were specifically designed to hold an MS-DOS filesystem, and that they take advantage of the fact that the MS-DOS filesystem uses redundant sectors on the first track (the FAT, which is represented twice). The second copy of the FAT is not represented on the disk.

High capacity formats are sensitive to the exact rotation speed of the drive and the resulting difference in raw capacity. That's why superformat performs a measurement of the disks raw capacity before proceeding with the formatting. This measurement is rather time consuming, and can be avoided by storing the relative deviation of the drive capacity into the drive definition file file. See section 5. Drive descriptions, for more details on this file. The line to be inserted into the drive definition file is printed by superformat after performing its measurement. However, this line depends on the drive and the controller. Do not copy it to other computers. Remove it before installing another drive or upgrade your floppy controller. Swap the drive numbers if you swap the drives in your computer.

10.10.1 Common Options  The most frequently used options
10.10.2 Advanced Options  For experts
10.10.3 Sector skewing options  Optimizing throughput by creatively arranging the sectors
10.10.4 Examples  Some example command lines
10.10.5 Troubleshooting  Most common failure modes
10.10.6 Bugs  Nobody is perfect


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.10.1 Common Options

Many options have a long and a short form.

-h
--help
Print the help.

-D drive
--dosdrive dos-drive
Selects DOS drive letter for mformat (for example a: or b:). The colon may be omitted. The default is derived from the minor device number. If the drive letter cannot be guessed, and is not given on the command line, mformat is skipped.

-v verbosity-level
--verbosity verbosity-level
Sets the verbosity level. 1 prints a dot for each formatted track. 2 prints a changing sign for each formatted track (- for formatting the first head, = for formatting the second head, x for verifying the first head, and + for verifying the second head). 3 prints a complete line listing head and track. 6 and 9 print debugging information.

--superverify
Verifies the disk by first reading the track, than writing a pattern of U's, and then reading it again. This is useful as some errors only show up after the disk has once been written. However, this is also slower.

-B
--dosverify
Verifies the disk using the mbadblocks program. mbadblocks marks the bad sectors as bad in the FAT. The advantage of this is that disks which are only partially bad can still be used for MS-DOS filesystems.

-V
--verify_later
Verifies the whole disk at the end of the formatting process instead of at each track. Verifying the disk at each track has the advantage of detecting errors early on.

-f
--noverify
Skips the verification altogether.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.10.2 Advanced Options

Usually, superformat uses sensible default values for these options, which you normally don't need to override. They are intended for expert users. Most of them should only be needed in cases where the hardware or superformat itself has bugs.

-b begin-track
--begin_track begin-track
Describes the track where to begin formatting. This is useful if the previous formatting failed halfway through. The default is 0.

-e end-track
--end_track end-track
Describes where to stop formatting. end_track is the last track to be formatted plus one. This is mainly useful for testing purposes. By default, this is the same as the total number of tracks. When the formatting stops, the final skew is displayed (to be used as absolute skew when you'll continue).

-S sizecode
--sizecode sizecode
Set the sector size to be used. The sector size is 128 * (2 ^ sizecode). Sector sizes below 512 bytes are not supported, thus sizecode must be at least 2. By default 512 is assumed, unless you ask for more sectors than would fit with 512 bytes.

--stretch stretch
Set the stretch factor. The stretch factor describes how many physical tracks to skip to get to the next logical track (2 ^ stretch). On double density 5 1/4 disks, the tracks are further apart from each other.

-G fmt-gap
--format_gap fmt-gap
Set the formatting gap. The formatting gap tells how far the sectors are away from each other. By default, this is chosen so as to evenly distribute the sectors along the track.

-F final-gap
--final_gap final-gap
Set the formatting gap to be used after the last sector.

-i interleave
--interleave interleave
Set the sector interleave factor.

-c chunksize
--chunksize chunksize
Set the size of the chunks. The chunks are small auxiliary sectors used during formatting. They are used to handle heterogeneous sector sizes (i.e. not all sectors have the same size) and negative formatting gaps.

--biggest-last
For MSS formats, make sure that the biggest sector is last on the track. This makes the format more reliable on drives which are out of spec.

--zero-based
Formats the disk with sector numbers starting at 0, rather than 1. Certain CP/M boxes or Music synthesizers use this format. Those disks can currently not be read/written to by the standard Linux read/write API; you have to use fdrawcmd to access them. As disk verifying is done by this API, verifying is automatically switched off when formatting zero-based.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.10.3 Sector skewing options

In order to maximize the user data transfer rate, the sectors are arranged in such a way that sector 1 of the new track/head comes under the head at the very moment when the drive is ready to read from that track, after having read the previous track. Thus the first sector of the second track is not necessarily near the first sector of the first track. The skew value describes for each track how far sector number 1 is away from the index mark. This skew value changes for each head and track. The amount of this change depends on how fast the disk spins, and on how much time is needed to change the head or the track.

--absolute_skew absolute-skew

Set the absolute skew. This skew value is used for the first formatted track. It is expressed in raw bytes.

--head_skew head-skew

Set the head skew. This is the skew added for passing from head 0 to head 1. It is expressed in raw bytes.

--track_skew track-skew

Set the track skew. This is the skew added for seeking to the next track. It is expressed in raw bytes.

Example: (absolute skew=3, head skew=1, track skew=2)

 
track 0 head 0: 4,5,6,1,2,3	(skew=3)
track 0 head 1: 3,4,5,6,1,2	(skew=4)

track 1 head 0: 1,2,3,4,5,6	(skew=0)
track 1 head 1: 6,1,2,3,4,5	(skew=1)

track 2 head 0: 4,5,6,1,2,3	(skew=3)
track 2 head 1: 3,4,5,6,1,2	(skew=4)

N.B. For simplicitie's sake, this example expresses skews in units of sectors. In reality, superformat expects the skews to be expressed in raw bytes.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.10.4 Examples

In all the examples of this section, we assume that drive 0 is a 3 1/2 and drive 1 a 5 1/4.

The following example shows how to format a 1440K disk in drive 0:
 
superformat /dev/fd0 hd

The following example shows how to format a 1200K disk in drive 1:
 
superformat /dev/fd1 hd

The following example shows how to format a 1440K disk in drive 1:
 
superformat /dev/fd1 hd sect=18

The following example shows how to format a 720K disk in drive 0:
 
superformat /dev/fd0 dd

The following example shows how to format a 1743K disk in drive 0 (83 cylinders times 21 sectors):
 
superformat /dev/fd0 sect=21 cyl=83

The following example shows how to format a 1992K disk in drive 0 (83 cylinders times 2 heads times 12 KB per track)
 
superformat /dev/fd0 tracksize=12KB cyl=83 mss

The following example shows how to format a 1840K disk in drive 0. It will have 5 2048-byte sectors, one 1024-byte sector, and one 512-byte sector per track:
 
superformat /dev/fd0 tracksize=23b mss 2m ssize=2KB

All these formats can be autodetected by mtools, using the floppy driver's default settings.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.10.5 Troubleshooting

FDC busy, sleeping for a second
When another program accesses a disk drive on the same controller as the one being formatted, superformat has to wait until the other access is finished. If this happens, check whether any other program accesses a drive (or whether a drive is mounted), kill that program (or unmount the drive), and the format should proceed normally.

I/O errors during verification
Your drive may be too far out of tolerance, and you may thus need to supply a margin parameter. Run floppymeter (see section 10.6 floppymeter) to find out an appropriate value for this parameter, and add the suggested margin parameter to the command line


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.10.6 Bugs

Opening up new window while superformat is running produces overrun errors. These errors are benign, as the failed operation is automatically retried until it succeeds.
[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.11 xdfcopy

 
xdfcopy [-format-id] [-d] [-n] [-h head-skew] [-t cylinder-skew] [-T
end-cylinder] [source] target

Xdfcopy is a utility to copy and format XDF disks. XDF (eXtended Density Format) is a format used by OS/2 which can hold 1840KB of data (on a 3 1/2 high density disk). Its advantage over 2m formats is that it is faster: 38KB/s. Because of this fast speed, I extended the XDF standard to higher capacities (1992KB) with a transfer rate of 45KB/s. I called the new formats XXDF.

This program works best with kernels newer than 2.0.0.

If both source and target are given, xdfcopy copies the disk image from file to floppy disk or vice-versa. When copying to a floppy disk, the disk is first formatted, unless the -n option is given.

If no source is given, the target is only formatted. In this case, the target must be a floppy drive.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.11.1 Options


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.11.1.1 Selecting a format

Formats are selected by the format_id. The following formats are understood:

0
Formats a 5 1/4 XDF disk (1520 KB, 45.6 KB/s).

1
Formats a 3 1/2 high density XDF disk (1840 KB, 38.3 KB/s).

2
Formats a 3 1/2 extra density XDF disk (3680 KB, 102 KB/s)

3
Formats a 3 1/2 high density XXDF disk (1920 KB, 45 KB/s)

4
Formats a 3 1/2 extra density XXDF disk (3840 KB, 90 KB/s)


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.11.2 Misc options

-D dosdrive
Describes the DOS drive letter for mformat. If this option is given, an MS-DOS filesystem is automatically installed on the disk after the low-level format is complete. In order for this to work, the drive has to be configured to accept the 23x2x80 geometry in your /etc/mtools or your ~/.mtoolsrc file. Moreover, this only works with a version of mtools that is more recent than 3.0.

Example of a working mtoolsrc line:
 
A /dev/fd0  0  0 0  0

Examples of a non-working mtoolsrc line:
 
A /dev/fd0 12 80 2 18

-n
Don't format the disk before copying the disk image to the disk.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

10.11.3 Options for power users

-t cylinder skew
Uses a different track skew than the default (14). For more details on skews, see section 10.10 superformat. In this version of xdfcopy, the -t parameter is ignored.

-h head skew
Uses a different head skew than the default (0) In this version, this parameter is ignored

-d
Debugging. For each read or write operation, the time it took to complete the operation is printed (in milliseconds). This can be used to optimize the skews.

-T end-cylinders
Tells how many cylinders to format. With the XXDF formats, it is actually possible to format up to 83 cylinders, yielding a format of up to 1992KB on a 3 1/2 high density disk.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

11. Compile-time configuration via GNU autoconf

Before it can be compiled, fdutils must be configured using the GNU autoconf script ./configure. In most circumstances, running ./configure without any parameters is enough. However, you may customize fdutils using various options to ./configure. The following options are supported:

--prefix directory
Prefix used for any directories used by fdutils. By default, this is `/usr/local'. Fdutils is installed in `$prefix/lib', looks for its system wide configuration file in `$prefix/etc'. Man pages are installed in `$prefix/man', info pages in `$prefix/info' etc.

--sysconfdir directory
Directory containing the system-wide configuration files such as `mediaprm' and `driveprm'. By default, this is derived from prefix (see above). N.B. For backward compatibility reasons, the old-style floppy parameter file `fdprm' is always in `/etc', regardless of the setting for sysconfdir

--enable-fdmount-floppy-only
Allows usage of the fdmount program only to members of the group floppy

In addition to the above-listed options, the other standard GNU autoconf options apply. Type ./configure --help to get a complete list of these.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

A. Acronyms

SD (Single density)
Single density disks use a data transfer rate of 125 kb/s and are no longer in use today, because of their low capacity.

DD (Double density)
Double density disks normally hold 360KB (5 1/4) or 720KB (3 1/2) of data per disk.

Double density disks have only a hole on one side (for write protection).

Double density uses a data transfer rate of 250 kb/s or 300 kb/s depending on the drive type: 5 1/4 high density drives use 300 kb/s when writing to a double density diskm 250 kb/s is used in all other circumstances. The reason why double density disks in high density drives need a higher data transfer rate is because these drives rotate faster (360 rpm instead of 300 rpm).

HD (High density)
High density disks normally hold 1200KB (5 1/4) or 1440KB (3 1/2) of data per disk. High density 3 1/2 disks are marked as such by the presence of a second square hole, just opposed to the write protect hole. 3 1/2 high density disks are the most commonly used type of disks today.

QD (Quad density)
Quad density is a hybrid between double and high density. It only exists for 5 1/4 disks, and holds 720KB of data. It can be obtained by formatting DD disks in a HD drive. QD uses double density for the density along the tracks (data transfer rate), and high density for the density perpendicular to the tracks (spacing between tracks, and thus number of tracks). This came to existence because these two aspects are limited by two different factors: the density along the track is limited by the quality of the media, whereas the density perpendicular to the tracks is mainly limited by the drive mechanism (this density, expressed in bits per inch comes nowhere near the limits of the media, even with HD). Thus quad density is an easy way to double the capacity of an ordinary double density disk, just by formatting it in a HD drive.

ED (Extra density)
Extra density refers to a disk density that can normally hold 2880KB of data per disk. Extra density disks only exist as 3 1/2 disks. ED disks are marked with a second squared hole opposed to the square hole, which is a little bit closer to the middle of the edge than that of HD disks. This format never really took off, because it only was released when storage media with a much higher capacity, such as CD-Roms, tapes and Zip disks became popular.

ED uses a data transfer rate of 250 kb/s.

DS (Double sided)
Self explanatory.

SS (Single sided)
Self explanatory

MSS (Mixed size sectors)
Mixed sector size formats are formats which use sectors of several different sizes on a single track. See section 6.6 Mixed sector size (MSS) formats, for details.

2M (2 Megabytes)
2M is a high capacity format developped by Ciriaco de Celis. The basic principle is the same as MSS: mix sectors of several sizes on a same track, in order to minimize both slack space and header overhead. 2M is different from MSS in that it uses a normal 18 sector format on its first track. See section 6.8 2M formats, for details.

rpm (Rotations per minute)
All 3 1/2 drives and 5 1/4 DD drives run at 300 rotations per minute, whereas 5 1/4 HD drives run at 360 rotations per minute.

rps (Rotations per second)
See above.

tpi (tracks per inch)
Expresses how close cylinders are to each other. Usually, 5 1/4 double density disks have 48 tpi, whereas 5 1/4 high density and quad density disks have 96 tpi. 3 1/2 disks use 135.5 tpi.

XDF (eXtended Density Format)
XDF is a disk format used for the OS/2 distribution disks. Its operating systems are similar to 2M and MSS disk, but it is faster due to a more creative arrangement of sectors. See section 6.9 XDF formats, for details.

XXDF (eXtended XDF)
XXDF is an Linux enhancement for XDF. It can store 1992 KB of data on an ED disk instead of just 1840 available with the regular XDF format. See section 6.10 XXDF formats, for details.

MFM (Multi Frequency Modulation)
MFM is a low level encoding of disk data. It is used for DD, HD and ED disks, i.e. virtually all disks that are available today. The PC hardware can only read MFM and FM disks. The doc at:
 
http://www.moria.de/~michael/floppy/floppy.ps
contains more detailed information about FM and MFM encoding.

FM (Frequency modulation)
FM is a low level encoding of disk data. It was used for SD disks, and is now considered to be obsolete. The doc at:
 
http://www.moria.de/~michael/floppy/floppy.ps
contains more detailed information about FM and MFM encoding.

kb (kilobit)
1000 bits

kb/s (kilobit per second)
We express the raw data throughput to and from the disk in this unit, which is also used in the documentation of the floppy disk controller.

B
Byte. A byte is 8 bits, and is the smallest individually addressable unit of data.

KB (K-Byte)
1024 bytes. Sometimes also noted K.

KB/s (K-Byte)
We express the usable data throughput to and from the disk in KB/s. Roughly, 1 KB/s = 8 kb/s. However, the usable data throughput is always lower than the raw throughput due to header overhead, interleaving and seek overhead.

MB (Megabyte)
Initially, 1 megabyte was 1024*1024 bytes (i.e. 1048576 bytes). However, when talking of floppy disk capacity, we understand it as 1000KB, that is 1000*1024 bytes, i.e. 1024000 bytes.

MB/s (million bytes per second)
We express (high) raw data throughput to and from the disk in kb/s, which is also used in the documentation of the floppy disk controller.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

B. Interesting formats

This table lists a few interesting formats. Some of them are not included in the table of predefined formats due to lack of space. You may use these by setting the geometry of the variable geometry device using setfdprm. Most of the entries in the following table do not describe a single format, but rather a family of formats which share a common characteristic. For this reason, no precise parameters are included.

80/90/160/180 KB 5.25"
Original IBM PC, CP/M, Apple II, TRS-80, etc. Single density, FM (not MFM), 40-track. Some systems also used "hard" sectoring, with an index hole for each sector. These are probably readable on standard FDCs if anyone cares to go to the effort. 160KB/180KB formats were double-sided.

320 KB 5.25"
CP/M, Zenith Z-100, some forms of MS-DOS. 8-sector DD 40-track.

400 KB 5.25"
AT&T 7300/3B1: cpio format, 10 sectors, DS, 40 tracks.

PC: MS-DOS, 10 sectors, DS, 40 tracks; formatted by various utilities; readable by some versions of MS-DOS.

<720KB 3.5" formats

720 KB 3.5"

720 KB 5.25"
"Quad Density": 9 sectors, DS, 80-track; name is rather misleading, as it is double density 80 track.

800 KB
880 KB

880 KB - 960 KB
Atari ST: 11/12 sectors, DS, 80-track, interleaved(?); not very reliable, formatted by various PD utilities.

960 KB
2m and Linux; 6 sectors interleaved(?), DS, 250kb/s?, 80-track, 1K sectors(?).

1001 KB
"Japanese" format: 300kb/s, 77 tracks, HD drives/disks.

1040 KB
2m and Linux only; 13 sectors, DS, 300kb/s, 80-track.

1120 KB
2m and Linux only; 14 sectors interleaved, DS, 300kb/s, 80-track. Can only be formatted on Linux; even on Linux, it is difficult to format these on an ED drive.

1200 KB 5.25" HD
"AT": 360 rpm 500kb/s 80-track 15-sector MS-DOS.

1360 KB 5.25" HD
Highest "fdformat" noninterleaved 5.25" format. 360 rpm 500kb/s 17-sector MS-DOS.

1440 KB 5.25" HD
Interleaved 18-sector 360 rpm 500kb/s; highest "fdformat" 5.25" format. 18-sector MS-DOS.

2m and Linux only: noninterleaved 1024-byte sector 18-sector-equivalent 360 rpm 500kb/s; 18-sector MS-DOS. A good substitute for 1.44MB 3.5" floppies.

1600 KB 5.25" HD
2m and Linux only: interleaved? 500kb/s 80-track; 1 8KB sector, 1 2KB sector?

1760 KB 3.5" HD
2m and Linux only: 11 1KB sectors; 500kb/s, noninterleaved?

1840 KB 3.5" HD
2m and Linux only: 23-sector equivalent; 500kb/s, noninterleaved.

1920 KB 3.5" HD
2m and Linux only: 3 4KB sectors; 500kb/s, interleaved?

2m and Linux only: 1 8KB sector, 1 4KB sector; 500kb/s, interleaved?

2880 KB 3.5" ED
"Extra Density" or "Extra High Density". 1 Mb/s, 36-sector, DS, 80- track.

3200 KB 3.5" ED
Non-interleaved, 80 track, 40-sector 1 Mb/s. Highest capacity that MS-DOS can read directly(?)

3520 KB 3.5" ED
2m and Linux only: 1 16KB sector, 1 4KB sector, 1 2KB sector? Non-interleaved, 80 track 1 Mb/s. Highest capacity that 2m can format.

3840 KB 3.5" ED
2m and Linux only: 1 16KB sector, 1 8KB sector (or is it 3 8KB sectors?). Non-interleaved, 80 track 1 Mb/s. Formatted only by Linux, but readable and writeable by 2m.

Linux is able to read almost any MFM disk. These include many CP/M disks and also Commodore 1581 disks. Please get Michael Haardt's documentation on floppy drives for a detailed description of those formats. This can be ftp'ed from the following location:
 
http://www.moria.de/~michael/floppy/

Commodore 1581 disks are not yet described in this documentation. Use setfdprm /dev/fd0 DD DS sect=10 cyl=80 swapsides. If you want to use these disks often, redefine one of the "default" formats to be Commodore 1581, and then put it into the autodetection list for the drive. The following example describes how to redefine format number 31 (minor device number 124) to be Commodore 1581:
 
mknod /dev/fd0cbm1581 b 2 124
setfdprm /dev/fd0cbm1581 DD DS sect=10 cyl=80 swapsides
floppycontrol --autodetect /dev/fd0 31,7,8,4,25,28,22,21

The two latter commands have to be issued after each reboot, so I suggest you put them into your `/etc/rc' files if you use many Commodore 1581 disks.


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

Command Index

Jump to:   D   F   G   M   S   X  

Index Entry Section

D
diskd10.1 diskd
diskseekd10.2 diskseekd

F
fdlist10.3 fdmount
fdmount10.3 fdmount
fdmountd10.3 fdmount
fdrawcmd10.4 fdrawcmd
fdumount10.3 fdmount
floppycontrol10.5 floppycontrol
floppymeter10.6 floppymeter

G
getfdprm10.7 getfdprm

M
MAKEFLOPPIES (making floppy devices)3. Device numbers

S
setfdprm10.9 setfdprm
setfdprm (Adding formats)3.4 Adding new formats
superformat10.10 superformat

X
xdfcopy10.11 xdfcopy

Jump to:   D   F   G   M   S   X  


[ < ] [ > ]   [ << ] [ Up ] [ >> ]         [Top] [Contents] [Index] [ ? ]

Concept index

Jump to:   2   8  
A   B   C   D   E   F   G   H   I   K   L   M   N   O   P   R   S   T   V   X  

Index Entry Section

2
2M6.8 2M formats
2M (mixed sector sizes)6.6 Mixed sector size (MSS) formats

8
83 cylinders6.4 More Cylinders

A
Adding formats3.4 Adding new formats
ALPHA patches1. Where to get fdutils and its documentation
autodetection7. How autodetection works
automounting10.3 fdmount
Available Formats3.3 The geometry list

B
bugs1. Where to get fdutils and its documentation
Builtin Formats3.3 The geometry list

C
CMOS type10.5.4 Drive type configuration and autodetection
Command list10. Command list
compile-time configuration11. Compile-time configuration via GNU autoconf
configuration of floppy driver10.5 floppycontrol
configure options11. Compile-time configuration via GNU autoconf
CPIO2.5.3 CPIO (CoPy In/Out)
cylinders6.4 More Cylinders

D
Default Formats3.3 The geometry list
detecting a disk change10.5.3 Printing current settings
determining drive type10.5.3 Printing current settings
device numbers3. Device numbers
diffs1. Where to get fdutils and its documentation
direct interaction with floppy driver10.4 fdrawcmd
disk absent during operation (false alert)10.5.5 Configuration of the disk change line
disk change detection10.5.5 Configuration of the disk change line
disk change line10.5.5 Configuration of the disk change line
drive type10.5.4 Drive type configuration and autodetection
dust (shaking it off from a drive)10.2 diskseekd

E
ejecting a disk10.5.2 One time actions
Ext22.6 Ext2 (Second Extended File System)
extended formats6. Storing more data on a floppy disk

F
Fdutils (brief list of supplied utilities)2.7.3 New Utilities
file name of floppy devices2.3 What's in a name
file systems supported by linux2.2 File systems supported by Linux
Fixed format devices3.2 Fixed format devices
floppy device name2.3 What's in a name
floppy ioctls9. Floppy ioctls
flushing floppy cache10.5.2 One time actions
format7. How autodetection works
format (low level vs. high level)2.1 How disks are organized
Format List3.3 The geometry list
Formats3.3 The geometry list
formatting disks6. Storing more data on a floppy disk
formatting disks (non XDF)10.10 superformat
formatting XDF disks10.11 xdfcopy

G
Geometries3.3 The geometry list
geometry information (reading back)10.7 getfdprm
geometry information (setting)10.9 setfdprm
Geometry List3.3 The geometry list

H
high capacity formats6. Storing more data on a floppy disk
high level format2.1 How disks are organized

I
indentifying unknown disks2.4 What to do if you get an unidentified floppy disk
interleave6.2 Using interleave
ioctl list9. Floppy ioctls

K
Kernel (new features)2.7.1 New features of 1.2+ kernels

L
larger sectors6.5 Larger sectors
List of available commands10. Command list
low level format2.1 How disks are organized
low level interaction with floppy driver10.4 fdrawcmd

M
mailing list1. Where to get fdutils and its documentation
making floppy devices3. Device numbers
Mixed sector size formats (2M)6.8 2M formats
Mixed sector size formats (XDF)6.9 XDF formats
Mixed sector size formats (XXDF)6.10 XXDF formats
more cylinder6.4 More Cylinders
more sectors per track6.1 More sectors per cylinder
MSS6.6 Mixed sector size (MSS) formats
MSS (2M)6.8 2M formats
MSS (XDF)6.9 XDF formats
MSS (XXDF)6.10 XXDF formats
Mtools (new features)2.7.2 New features of mtools-3.0
mtools (nickel tour)2.5.1 mtools

N
name of floppy devices2.3 What's in a name
New features2.7 New Features of 1.2+ kernels
nickel tours2.5 Nickel tours

O
OS/2 (XDF)6.9 XDF formats

P
patches1. Where to get fdutils and its documentation
printing current settings10.5.3 Printing current settings

R
raw capacity10.6 floppymeter
raw command10.4 fdrawcmd
reading back the geometry information10.7 getfdprm
recognize a disk7. How autodetection works
Redefining formats3.4 Adding new formats
resetting controller10.5.2 One time actions
rotation speed10.6 floppymeter

S
sector skewing6.3 Sector skewing
sectors per track6.1 More sectors per cylinder
setting the geometry information10.9 setfdprm
shaking off dust from a drive10.2 diskseekd
skewing6.3 Sector skewing
strange noises during seek10.5.6 Timing Parameters
supported file systems2.2 File systems supported by Linux
swapping drives10.5.4 Drive type configuration and autodetection

T
tar2.5.2 Tar (Tape ARchive)
Thinkpad10.5.5 Configuration of the disk change line
tracks6.4 More Cylinders

V
Variable format devices3.1 Variable format devices

X
XDF6.9 XDF formats
XDF (formatting and copying disks)10.11 xdfcopy
XDF (mixed sector sizes)6.6 Mixed sector size (MSS) formats
XXDF6.10 XXDF formats

Jump to:   2   8  
A   B   C   D   E   F   G   H   I   K   L   M   N   O   P   R   S   T   V   X  


[Top] [Contents] [Index] [ ? ]

Footnotes

(1)

In that case, the MAKEFLOPPIES program (10.8 makefloppies) no longer works to generate a correct name for these formats, and you have to make them manually.

(2)

The actual location of this file depends on the value of the sysconfdir compile time configuration variable (see section 11. Compile-time configuration via GNU autoconf for details)

(3)

drives do not always rotate at exactly 5 or 6 rotations per second, but some may be slightly faster or slightly slower than spec

(4)

The actual location of this file depends on the value of the sysconfdir compile time configuration variable (see section 11. Compile-time configuration via GNU autoconf for details)

(5)

except of course if several formats only differ in the number of sectors per track, in which case the formats with the most sectors should come first

(6)

Version 3.0 or higher


[Top] [Contents] [Index] [ ? ]

Table of Contents


[Top] [Contents] [Index] [ ? ]

Short Table of Contents

General Introduction
1. Where to get fdutils and its documentation
2. Basic usage
3. Device numbers
4. Media description
5. Drive descriptions
6. Storing more data on a floppy disk
7. How autodetection works
8. Configuring the floppy driver via lilo or insmod
9. Floppy ioctls
10. Command list
11. Compile-time configuration via GNU autoconf
A. Acronyms
B. Interesting formats
Command Index
Concept index

[Top] [Contents] [Index] [ ? ]

About this document

This document was generated by Alain Knaff on March, 3 2005 using texi2html

The buttons in the navigation panels have the following meaning:

Button Name Go to From 1.2.3 go to
[ < ] Back previous section in reading order 1.2.2
[ > ] Forward next section in reading order 1.2.4
[ << ] FastBack previous or up-and-previous section 1.1
[ Up ] Up up section 1.2
[ >> ] FastForward next or up-and-next section 1.3
[Top] Top cover (top) of document  
[Contents] Contents table of contents  
[Index] Index concept index  
[ ? ] About this page  

where the Example assumes that the current position is at Subsubsection One-Two-Three of a document of the following structure:

This document was generated by Alain Knaff on March, 3 2005 using texi2html